Jump to content
SAU Community

Recommended Posts

FOR SALE

500 + HP

R31 1988 Skyline Silhouette.

IN Gray over silver - Straight as body

Was featured in Issue 6 of Boost or zoom mag when changed name.

Engine specs

Are fully rebuilt strengthend top to bottom RB30ET with custom cam and GT42 by GCG

Full Plazmaman intake manifold and intercooler plumbing packaged done by Plazmaman

Autronic ECU.

Engine is Tune by DART and made 525RWHP on his dyno on 26PSI.

Transmission is jatco 4 speed with transbrake. 3500rpm stall and LSD etc.

Boxed rear end

It's Run a best of 140MPH 10.0 sec at WSID In Complete street trim no lightening and NO exahsut dumped etc. Only difference was C16 used in the fuel mix. On street running 16psi 98RON pump fuel.

Car has no cage, Interior is clean complete and original.

Brake upgrade 300ZX 4 spots and rotors

Price $21,000 - ONO.

Contact at E-mail here

peter31copy.jpg

peter31jcopy.jpg

peter31acopy.jpg

peter31ecopy.jpg

peter31fcopy.jpg

Rb30 block - 20thou over bore - drilled and tapped for 1/2inch head studs.

ARP main studs for girdle and head.

Cosmetic multi layer head gasket

Argo Rods -

CP forgged oversized 20thou pistons

Fully balanced bottomend

oversize stainless valves - mild port polished head

Custom Cam.

custom exhaust by MTS manifolds and intake bottom half extrude honed.

never been apart since built.

if you want more details phone.

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...