Jump to content
SAU Community

Recommended Posts

Turned up the bleeder to get more power. With the stock ECU I couldnt run more than 10psi without running into misfire problems (which is the most infamous problem with 33 ecus). The chipped ecu has a much better ignition timing so I can push to boost to turbo annihilation :D

The overall power figure is not too much greater than the stock ecu but the car pulls to the redline A LOT quicker than before. People seem to forget its not just the top end power figure, its a combination of how quickly you can get there. If I had a scanner I'd post the before and after curves but alas I do not.

  • 2 weeks later...

The re-mapped ECU has a higher boost (afm) cut than stock which allowed us to increase the boost a little. apart from that there were signifcant gains in mid range response, not to mention the removal of the 180 km/h speed limiter.

All nissan ECU's are reprogrammable. I have found the adaptors for the RB25 and late model RB26 ones and just parts is over $900 per ECU :D

All other nissan ECU's are easily remapped.

Doc.

Interesting...my 33 is completely stock and I just discovered the 180km/h speed cut is disabled...(I think...the needle just kept going into the blackness)

I had a look for cut wires or switches that look aftermarket but couldn't find any and the ecu looks stock as a rock this is very weird...any ideas?

I managed to take it apart... just took blurry photo

Can you tell if this is stock?

:)

http://www.skylinesaustralia.com/forums/at...achmentid=10182

Nick - Check the MEC number on the main EPROM, if it matches the MEC number on the outside of the ECU then it's stock.

J

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...