Jump to content
SAU Community

Stagea Parts! And Some R33 Gtr Bits That Fit

OoskylineoO
 Share

Recommended Posts

OoskylineoO Experienced

OoskylineoO

Posted
Posted

Have a few bits and pieces off a stagea and R33 GTR

Parts list and prices

Whiteline Rear Upper Control Control Arm Bushes BRAND NEW W0579, $70ono

Genuine Momo Steering wheel. Typ D35 KBA 70116 is the model. In excellent condition, only very minor wear marks. $170ono

R33 GTS4 stock shocks w/ aftermarket springs, Shocks are in ok condition, no signs of leaks. As for springs there in good condition just not 100% which brands they are, being red, either pedders, nismo or apexi springs?. They might be pedders but I'm not 100%. Came off R33 GTS4, assuming they may fit (correct me if wrong). $200ono

R33 Series 2 VCT N/A Motor RB25DE 147kw, 114,000kms motor is in A1 condition, regularly serviced synthetic oils. Pulled out of running vehicle. DROPPED PRICE TO $550ono take it now or it goes to my friend soon. Includes 4WD Sump and Front Diff and shaft, wiring loom and ecu iridium plugs, exhaust manifold and intake pipe. Drops straight into a stagea.

NOTE: Took off some parts as I needed them. These include, water pump, tensioner and idle bearings, harmonic balancer, A/C and pwr/steer pump. So just pretty much the 100,000km service.

R33 GTS4 Series 2 4WD Gearbox . 114,000kms in good working condition, I beleive it bolts up to stageas as well. $400ono

R33 GTR Front 5 Stud Hub Assembly $150ono

Stagea Front swaybar $20

Stagea Rear swaybar $20

Stainless steel Cannon Muffler Angle Cut Tip - 2.5'' Inlet, 5.5'' Barrel, 4.5'' Angle cut Tip

Very good condition no dents, came off R33 $40ono

RB20/RB25 Crossover pipe in good condition - $20

Gates Timing belt used 10,000kms only $45ono

RB25 Flywheel, Factory in good condition fits RB20 as well. $45

PICS UPON REQUEST

0412 297 325

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...