Jump to content
SAU Community

Engineer To Comply My 89 Gtst In Victoria

f1750
 Share

Recommended Posts

W0rp3D Grand Master

W0rp3D

Posted
Posted
Hi guys i have to get my gtst 89 on the road here in vic. I need some contact details of a good engineer to comply the car to the 15 year old import rules and a contact to weld/tack intrusion bars in doors thanks louis

15yo import rules dont exist anymore, you have to go through full compliance and you need a workshop who has a sevs licesne to do it, contact vic roads they will give you a list.

BigWillieStyles Enthusiast

BigWillieStyles

Posted
Posted
Howdy baron i imported it 7 years ago as a 15 year car

its a standard approval

thanks

louis

In that case you can comply it under the 15 year rule. There is a list of engineers for Vic around somewhere, perhaps the VicRoads website.

Beer Baron Grand Master

Beer Baron

Posted
Posted
Howdy baron i imported it 7 years ago as a 15 year car

its a standard approval

thanks

louis

hi Louis, when you say 'standard approval' there isn't really such a thing. if it was 7 years ago it may well have been imported under the old LVIS (Low Volume Import Scheme). In that case you may be out of luck. if you imported it 7 years ago that was 2002. in 2002 we could only import cars built up to 1987 under the 15yo rule so in that case your car was definitely not a 15yo car. it may be too late to have it complied under it's current import approval. if you still have it can you post a scan of it up? feel free to black out your name, the chassis number, approval number etc but it will at least mean we can give you some advice.

edit: just read your post properly, you say it was a 15yo import approval but if it was 7 years ago I don't see how you could get an 89 GTST? Anyway assuming you do have it imported under the 15yo rule you should be able to just go through the basic requirements for it to be able to be registered in your chosen state. They might ask some questions as to why you didn't get it done in the last 5 years or so.....

  • 2 weeks later...
f1750 Rookie

f1750

Posted
  • Author
Posted
hi Louis, when you say 'standard approval' there isn't really such a thing. if it was 7 years ago it may well have been imported under the old LVIS (Low Volume Import Scheme). In that case you may be out of luck. if you imported it 7 years ago that was 2002. in 2002 we could only import cars built up to 1987 under the 15yo rule so in that case your car was definitely not a 15yo car. it may be too late to have it complied under it's current import approval. if you still have it can you post a scan of it up? feel free to black out your name, the chassis number, approval number etc but it will at least mean we can give you some advice.

edit: just read your post properly, you say it was a 15yo import approval but if it was 7 years ago I don't see how you could get an 89 GTST? Anyway assuming you do have it imported under the 15yo rule you should be able to just go through the basic requirements for it to be able to be registered in your chosen state. They might ask some questions as to why you didn't get it done in the last 5 years or so.....

Thanks a bunch ill ring Vic Roads
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...