Jump to content
SAU Community

Recommended Posts

Item Summary: rb20det complete motor, gear box, loom and power fc

Location: mackay qld 4740

Condition: Used

Reason for Selling: putting a 26/30 in my car

Asking Price: 2500 Ono possibly seperate or swaps for rego'd car or 250cc road bike

Delivery Methods: PickUp or post

Contact Info: pm here or 0432470609

Extra Information:

hey guys i am selling my rb20det out of my 32, its been running real sweet for the last 2 yrs, it comes with every thing except for injectors, will get pics up tomorrow, can post if need be, still in car if u want to hear running or even take it for a drive, its got about 300hp (not 100% sure on that last dynoed it had 278hp but has had tune up since)

remember u get it all = turbo, intake, inlet, gear box, loom, 26 power fc modded for 20 by professional's and motor

was tuned by Johno Pace (mafia on here) ask him how well it goes if u want

would really like $2500 for it all not willing to go much more lower or will trade for a cheap car

thanks blocka

call or txt 0432470609

Separate FC from motor?

How much?

$1000?

yeah bud $1000 if some one else buys the motor and box and loom

ok everyone change of plans engine comes wih every thing now so injectors are included and they are 700cc sards

so for everything for a straight drop in and fire up set up $3000 or swap for a rego'd car or 250cc road bike

Edited by blockasR32

Ok considering seperating, if I get enough interest the fc will go to R32Abuser so who wnts the engine and box

Ok guys considering seperating but need some interest in it

PFC- $1000 or $1200 with loom

Engine- $1500 with injectors, turbo the works and standard coilpacks

Gearbox- $500

prices aren't 100% firm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...