Jump to content
SAU Community

Recommended Posts

As topic title states, chasing rb26 block, bare block only

perhaps crank to depending on condition.

located sth east burbs melb, but willing to drive if need be.

put this post up a few months ago and had one lined up but lost contact

and deleted my messages.

any help much appreciated

contact: pm or sms 0423292542

cheers, brad

Link to comment
https://www.sau.com.au/forums/topic/297441-wtb-gtr-block/
Share on other sites

not what your after but tangomatt off these forums has a 8,000km old nur engine fs in melb. pm him if your interested.

or: http://www.skylinesaustralia.com/forums/Gt...mm-t296869.html

Link to comment
https://www.sau.com.au/forums/topic/297441-wtb-gtr-block/#findComment-4952722
Share on other sites

As topic title states, chasing rb26 block, bare block only

perhaps crank to depending on condition.

located sth east burbs melb, but willing to drive if need be.

put this post up a few months ago and had one lined up but lost contact

and deleted my messages.

any help much appreciated

contact: pm or sms 0423292542

cheers, brad

im in melb i have a few around im asking $700 pm me if needed

Link to comment
https://www.sau.com.au/forums/topic/297441-wtb-gtr-block/#findComment-4953457
Share on other sites

Have one std bore and has been decked. Was removed due no.6 ring land. Has a crack between head bolt hold and one water jacket. Won't effect a stdish car. $100.

Would have used it but had already bought another motor before I stripped it.

Link to comment
https://www.sau.com.au/forums/topic/297441-wtb-gtr-block/#findComment-4957404
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...