Jump to content
SAU Community

Recommended Posts

  • Replies 196
  • Created
  • Last Reply

Top Posters In This Topic

Information update

Update

Plans are being finalised

What you have to wear

- you need a hemet

- long sleave shirt

- full length pants (including passengers)

Passenger are allowed however to cover insurance there will be a cost of $30 per passenger [/size](45 if you want to be fed) on the day, if passengers wish to be fed on the day there will be an additional charge of 15 bux, so for 45 bux you get a day of scaring yourself and you get fed (note only people who pay up front will be catered for because the food money is paid form my own pocket at I will be only covering people entered in the event)

Looks like its going to be huge and yes we are getting some prizes as first stated

Cheers

pete

0409226626

for the slackers

people in are listed below:

1.B-man (deposit 100)

2.Me

3.Sato

4.Sato's mate

5.bro (payed 150).

6.banzi (deposit 100) is that you phill brook??? or is that toomuch boosts deposit

7.mark hooker

8.mick cain

9.scotty

10.bakadesu (deposit 100).

11.manjana (deposit 30).

12.toomuchboost (deposit 100)

13 redx Payed (150).

14 slo200 (100).

15 Aaron - 180SX (payed 150 mick).

16 Adam - VL Turbo (payed 150 mick).

17 Andrew - Vx SS (payed 150 mick).

18 Paul - LX Torana (payed 150 mick).

19 Blake - Datsun 1600.(payed 150 mick).

20 lozz (deposit 100).

21 Van der wagon (deposit 100).

22 anthony reed (deposit 100)

23 matthew ladewig (paid 150)

24 kristian han**** (paid 150)

25 lockie grey (Deposit 100)

26

27

28

29

30

I see the Oran Park website has started promoting drift days.

www.oranpark.com

"A full release will be made shortly, but Oran Park can announce that there will be a professional drifting event held as part of Motorama on february 22. Drifting fans will see the best drifters in the country up close".

"The event on February 22 will be for professionals only. If you think you have what it takes, Oran Park will be soon be announcing opportunities for drivers to bring their road cars onto certain parts of Oran Park to practice drifting and possibly even compete in specially organised events".

Here is a pic of the North circuit for those who have not been to oran park...

Oran%20Park%20North.gif

I gather we will most likely take the inside road between the shell and champion corner like the go carts do...?

I am still waiting for my car to get off the boat....Can I just come along as a spectator ?

I do not mind paying for food....I have a helmet if I can be a passenger with someone.

Please PM me the details to pay.

Thanks

Mal




  • Similar Content

  • Latest Posts

    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
    • One way of putting the fuel surge idea to rest, is that even when in neutral/clutch in or free revving it still has the same issue, it can’t even get to limiter (7800) so to me that says it can’t be g force, I’m not trying to argue I just want to find the f&$king issue 😡
×
×
  • Create New...