Jump to content
SAU Community

Recommended Posts

Hi i have a 2000 R34 Non Turbo.

I had a basic service completed last week. I drove it home 150kms without a problem.

But the next day, the engine malfunction light came on and my car is shaking/shuddering.

It has been doing this each time i warm my car up.

I have been told by a few people it could be sparkplugs.

I dont want to drive my car back to mechanic and was wanting peoples opinion on the problem?

Thanks :nyaanyaa:

Mad082 - i will check my coil pack, i assume i will be able to find instuctions how to on a forum...

Moodles2 - thats the problem, im not sure exactly what they did in the service. I asked for a basic service so im assuming it was only the basics, i know they didnt change the sparkplugs as they were long life.

I have taken my car into RACV today to have it tested on the computer and 2 codes came back.

They were: Ignition Primary Code Auto and Transmission Manuel Mode Swith Code

They erased the codes, however it has made no difference to car.

Could it be sparkplugs? Can i please have other opinions?

My engine light would come up every now and again when one of my coil packs was dieing it was hardly noticeable, miss fired for a split second and then when back to normal, gradually getting worse. I got them all replaced and now a few months later it started doing it again constantly so i got new spark plugs but it didn't help at all, so i tried an injector cleaner (even after nissan had checked it and couldn't find a problem with the car) and now its running pretty sweet. Must be some shit petrol around at the moment, iv always used premium fuel so I'm guessing that water has gotten into my petrol tank or into the tanks at the petrol station?

Edited by R34 -_-
  • 1 month later...

I have since had my car tested on a DYNO and have been told it is a the crank angle sensor.

I have to wait until Feb to get one unless i pay $1000 through nissan.

2 questions!!! please help!

1 - does anyone know where in melb/vic i can get a crank angle sensor?

2 - is it an easy job to change the sensor? what needs to be done after changing? (do u need to tune it etc?)

Thank you :blink:

Ring around wreckers to see if you can find one. Theres a link in the Victoria section for wreckers.

You should have the car tuned with a new crank angle sensor installed, preferably on a dyno which will give you both maximum economy and power. If you dont want the expense, just set the base timing with a timing light.

Its very easy to change the crank angle sensor but if you tighten it up in the wrong spot, it could destroy your motor after a few minutes of driving. One millimeter forward or back of where it is could cause detonantion, or pinging.

Who has done the work for you so far?

Ring around wreckers to see if you can find one. Theres a link in the Victoria section for wreckers.

You should have the car tuned with a new crank angle sensor installed, preferably on a dyno which will give you both maximum economy and power. If you dont want the expense, just set the base timing with a timing light.

Its very easy to change the crank angle sensor but if you tighten it up in the wrong spot, it could destroy your motor after a few minutes of driving. One millimeter forward or back of where it is could cause detonantion, or pinging.

Who has done the work for you so far?

you would have to have an engine on it's last legs to let go due to a few mins of driving with detonation. plenty of people have driven round for months or even years with the engine pinging it's arse off due to being too lean from blocked fuel filters or dodgy fuel pumps.

you would have to have an engine on it's last legs to let go due to a few mins of driving with detonation. plenty of people have driven round for months or even years with the engine pinging it's arse off due to being too lean from blocked fuel filters or dodgy fuel pumps.

So pinging is OK?

You're right it's unlikely to destroy itself immediately. Either is driving on a flat tyre. Both are undesirable and lead to expensive and serious damage.

no i'm not saying it's ok, i'm just saying that it isn't a "OMG my engine is going to blow up and kill me and destroy the world" type of situation. hell, a large amount of pinging goes undetected as it isn't audible inside the cabin. and anyone with a stock ecu (or a nistune) shouldn't be overly concerned as the factory ecu will back off the timing if it hears it, providing the knock sensors are working properly.

  • 1 month later...

Just look on ebay or wherever, it's pretty easy to find splitfire or yellow jacket coil packs to replace your *insert car model here*

Edited by mosquitocoils

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...