Jump to content
SAU Community

Recommended Posts

i i just bought 20s to put on my r32 the back wheels clear fine

but the front wheels hit the top part of the suspension i think its called the stub axle maybe?

any ideas? besides gettin smaller wheels...

haha it's not the stub axle. It's the suspension arm that mounts to the top camber arm. You'll have to go skinny rims if you wanna make them fit. 20's make 32's look like matchbox cars anyway.

Do a search. It's been covered before in this section.

haha it's not the stub axle. It's the suspension arm that mounts to the top camber arm. You'll have to go skinny rims if you wanna make them fit. 20's make 32's look like matchbox cars anyway.

Do a search. It's been covered before in this section.

obviously i have no idea.

ye thats the look im goin for ;) cheers

dont do it!

or if you must get 20s - sell your skyline and buy a commo or falcon

haha to everyone 20's are like comitin suicide.

yer well im gna try swap for some 18s so everyone can just relax.

ps. fk commos an falcons

i i just bought 20s to put on my r32 the back wheels clear fine

but the front wheels hit the top part of the suspension i think its called the stub axle maybe?

any ideas? besides gettin smaller wheels...

If you're going to be a pimp you might as well go the whole hog and get a Century

http://en.wikipedia.org/wiki/Toyota_Century

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...