Jump to content
SAU Community

Recommended Posts

Hey all ,

i have a R33 GTR with a Mines ECU in it and the Limiter is set very close too 9,000 RPM and i dont really like that too be honest and it is running very rich which i believe could hinder the performance of the car im in sydney and was wondering are these ECU re programmable or if i can set the limiter a bit lower and make it a bit leaner without hurting the engine what so ever.

i am willing to pay if some one can help me out .

Thanks Guys :laugh:

Link to comment
https://www.sau.com.au/forums/topic/299344-mines-ecu/
Share on other sites

Hey all ,

i have a R33 GTR with a Mines ECU in it and the Limiter is set very close too 9,000 RPM and i dont really like that too be honest and it is running very rich which i believe could hinder the performance of the car im in sydney and was wondering are these ECU re programmable or if i can set the limiter a bit lower and make it a bit leaner without hurting the engine what so ever.

i am willing to pay if some one can help me out .

Thanks Guys :laugh:

Send it to DrDrift or anyone who can do Nistune.

Start saving for turbos though, they won't last too long once you lean the fuel out

Link to comment
https://www.sau.com.au/forums/topic/299344-mines-ecu/#findComment-4976266
Share on other sites

Hey all ,

i have a R33 GTR with a Mines ECU in it and the Limiter is set very close too 9,000 RPM and i dont really like that too be honest and it is running very rich which i believe could hinder the performance of the car im in sydney and was wondering are these ECU re programmable or if i can set the limiter a bit lower and make it a bit leaner without hurting the engine what so ever.

i am willing to pay if some one can help me out .

Thanks Guys :(

These ecu's depending on the "exact" tune work pretty well, i have had some come through which were pretty close (making 230-240rwkw) to being spot on, BUT many are generic loaded tunes and run mega rich from the mid range onwards. The limiter is most likely 8800 as most jap limiters are set there as it saves the oil pump (less chance of accidently hitting limiter), they are not pointless limiter bashers like many morons in this country :laugh:

Depending on the ecu (33 or 32) as many R33 come with remaped R32 ECU's as the R32 ecu is half the price to modifiy. If it is a R32 GTR ecu you can fit a nistune board to it or burn a new chip for it. I reccomend the Nistune as it allows live tuning and no chip burning.

We usually install a Nistune board (fully programmable) to it with an adjusted setup to suit 14-15psi and 98ron if it is the R32 GTR ecu, if its the R33 ecu you are stuck as no-one does them. Post a pic of the silver sticker on the ECU and i can tell you what model it is.

My reccomendaion if it is a R33 ECU is to buy a R32 GTR ecu and get unigroup to do a nistune conversion to it.

Edited by URAS
Link to comment
https://www.sau.com.au/forums/topic/299344-mines-ecu/#findComment-4976294
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...