Jump to content
SAU Community

Recommended Posts

Nissan Skyline R33, Non Turbo (P Plate Legal) RB25DE.

5 Speed Manual, With Low Original Kms, Only 94,000!!

Immaculate Condition Inside and Out, Always Garaged.

The Car Runs Perfectly, Never Missed A Beat And Is Very Reliable With Good Fuel Economy And Serviced Regularly.

Car Has Been Lowered A Couple Of Inches, And Has A Nice 2 1/2 Inch Exhaust System.

Also, Car Has Recently Been Resprayed And A New Lip Spoiler (Duck Wing) Has Been Put On.

Interior And Exterior Is In Perfect Condition.

A Very Clean Car, You Must See For Yourself.

Genuine But Regretful Sale.

$10,500 ONO

Car Comes With RWC And Registration Untill March 2010.

Contact: Adam - 0401 321 013.

post-52996-1260501647_thumb.jpgpost-52996-1260501723_thumb.jpg

post-52996-1260501780_thumb.jpgpost-52996-1260501838_thumb.jpg

post-52996-1260501892_thumb.jpg

the price has increased now because the car i wanted to buy is now sold. i only dropped the price to $10,500 because i really wanted that car so i was hoping it would sell by then.

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...