Jump to content
SAU Community

Recommended Posts

Yup met Adrian on the friday nite. I was walking up to the Maccas with 2 mates and seen this absolutely smick white R34, then after noticing the C/F bonnet I thought it was R34GTT-R's, just hadddd to say hello even if it wasn't his.

I'd have to say the best (if not 1 of the best) R34 GTT's I have ever seen (picture or in person). It sounded so horny when he took off too, lucky their was so many people around otherwise their may have been a mess :whackit:

Link to comment
https://www.sau.com.au/forums/topic/30022-nats/page/4/#findComment-638736
Share on other sites

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

The Nats was crazy!

Unfortunately i didn't get to meet anyone from this forum :rofl:, but did see a few Skylines ;).

I did ask about 4 people wether they were from the forum, all said no ;), felt awkward (sp?) asking "every single" skyline driver if they were from SAU.

Here is a pick of my mates car, i was always the front seat passenger, just in case you recognize the car.

Link to comment
https://www.sau.com.au/forums/topic/30022-nats/page/4/#findComment-640255
Share on other sites

i saw that car getting around, looked pretty sweet. i was kicking around braddon afterwards, saw a few skylines around but didn't want to make a fool of myself asking randoms if they were on SAU. i avoided lonsdale as it was bumper to bumper, plus Mr RTA doesn't aprove of my car.

Link to comment
https://www.sau.com.au/forums/topic/30022-nats/page/4/#findComment-640575
Share on other sites

the painful thing was that monaro had a fair bit of rear end damage, looked like it had hit something or something had hit it. that supercharger/whatever thingy was bigger than the car, im surprised it didn't tear itself off

Link to comment
https://www.sau.com.au/forums/topic/30022-nats/page/4/#findComment-643375
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...