Jump to content
SAU Community

Guy's Cruise Control Stuck On 80 Km/h


Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

i wonder if its one of these electronic boxes where computer selects the gears.. I used to drive a Merc sprinter with the tiptronic box and often they would jam...Gear stick doesnt actually connect to anything mechanical

http://www.heraldsun.com.au/news/driver-ta...o-1225810668864

Audio released from the 000 call.

Earlier today, Mr Weir hit back at critics who said he didn't do enough to avert a potential disaster.

heraldsun.com.au and talkback radio has been inundated with comments from people questioning why Ford Explorer driver Chase Weir didn't turn off the engine or put his car into neutral when he realised the vehicle was out of control.

Mr Weir has one message for the knockers: "You weren't in the car.''

Does his situation remind anyone of the 1997 movie "runaway car"

After visiting the mechanic, the car mysteriously and intermittently goes full throttle. To cut a long story short the movie is similar to speed.

Some epic moments too including a guys bright idea to crawl out of the car and remove spark plugs! Highly entertaining (Alcohol recommended whilst viewing)

http://www.imdb.com/title/tt0120041/

Edited by lukebaldan

This sounds like a total crock to me.

I smell some attention seeking kid.

Agreed.

I used to know someone who worked in the area of investigating these types of claim for a japanese manufacturer. The crap that people try to blame on cars is amazing. Americans are famous for it..

Anyway; just for laughs, the other day, I was driving my towing mule 4x4 down the eastern (late at night, empty road). I pushed my accelerator to the floor, then tried to use the brake to decelerate from 100. Slowing the car needed some leg muscle, but was possible. My 4x4 has nearly twice the torque of a ford explorer (650nm) and significantly more power.

I could believe that this kid couldn't get the car down to stopped with just the brakes; but slowing down to less than 80 wasn't possible? Bullshit.

The only explanation I can think of is that the car was in shitty condition (ie: brake pads worn out or something like that).

Failure of a single system isn't that unusual. Failure of all these things at once (cruise disable on braking, ignition jam, trans locked into auto, brake effectiveness unable to slow the V12 down to less than 80kmh etc). Smells like a dumb kid trying to get his 15 minutes of fame..

Classic pictures of him in a neck brace on a stretcher after he stopped, yet he didn't hit ANYTHING, and apparently couldn't even stop quickly. I smell a scam/nutjob....

im from wa and i herd this in the news and i thought i needed to post my opinion.

first i think this guy is full off shit or is f**king retarded.

if i was in his situation i would first apply the brakes and keep them on till i stop then put it in neutral then kill the engine putting the key to acc so i dont lock the steering then if all else fails back end a truck to really kill the engine and if it is still going down shift in to 1st (this can be done on a auto but dont ever EVER down shift 2 1st unless ur stopped or ur cruse control is f**ked :banana: )

there is going 2 be a investigation and it will be interesting 2 see the out come

im from wa and i herd this in the news and i thought i needed to post my opinion.

first i think this guy is full off shit or is f**king retarded.

if i was in his situation i would first apply the brakes and keep them on till i stop then put it in neutral then kill the engine putting the key to acc so i dont lock the steering then if all else fails back end a truck to really kill the engine and if it is still going down shift in to 1st (this can be done on a auto but dont ever EVER down shift 2 1st unless ur stopped or ur cruse control is f**ked :banana: )

there is going 2 be a investigation and it will be interesting 2 see the out come

On a lot of cars, shifting to a low gear while doing a higher speed in an auto will do nothing.

It will keep the car in a more appropriate gear to prevent damage to the motor.

Gone are the days when you could just remove the centre pin from your horse saddle and let the wagon roll to a stop just shy of a cliff edge.

Thats gold, what a chicken test!!!

I smell some attention seeking kid. Don't believe that his cruise got stuck...

My "theory" - He probably got busted speeding or doing something illegal and to cover it up faking his cruise control screwing up.... as a bonus he would make the evening news, and how would you get whiplash from hard braking....

Sounds way too sus....

Could be true

From what ive read and heard (they released 000 call) obviously there is a fault. The cruise control switch has caused fires in the states, possibly his ford had the same switch, and got stuck but did not cause the fire. Most of the fires that occured in the states the car was on long stretches of road, possibly not knowing that the switch had stuck and thats when the fire occured(not 100% sure though). I think it sounds a little strange but who knows, maybe he really couldnt get the car into neutral. The car was auto. I think kicking in the kick panel and busting some fuses wouldve been a good idea, not sure if the important fuses in the ford needed to stop the car would be in there, arent they mainly under the bonnet in most cars??

The cops thought of many ways to stop the car from getting a truck in front of hit to slow it down, to running the car into a paddock with long weeds whilst blowing the tyres out with spikes.

Very interesting situation to be in, one that i wouldnt want to be in.

I do believe the guys cruise control was stuck on, it has happened to many times to other people for me to believe that it really not happen.

On a lot of cars, shifting to a low gear while doing a higher speed in an auto will do nothing.

It will keep the car in a more appropriate gear to prevent damage to the motor.

i can down shift my auto yes some of the newer cars will stop real aggressive shifting but the car in question is not new.

and im my experience auto boxes ar computer controlled but neutral has a mechanical link via cable that should by pass the ecu. i dont know about Chase Weirs car :)

Actually my old Ford '96 model, when you brake cruise control is de-activated automatically, you can accelerate but braking manually causes cruise control to back down....

Did some quick research, the newer Ford's often have issues with this deactivation mechanism.

I'm an ex ford parts interpreter, the cruise control deactivation is wired up to your brake light switch, tail lamps come on, cruise cuts off, you step on the gas (no brake lights) doesn't turn off, most car makers work this way.

Ive had a few customers come in to buy new brake light switches as there cruise wont come off unless them put a fair amount of pressure on the brake pedal.

This case just seems like the exploder was possessed!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...