Jump to content
SAU Community

Recommended Posts

Hey peoples,

R34 GTT Power FC with commander for sale - $1500 FIRM - We all know how rare they are!

Blitz R34 GTT Injectors - From memory they are 525CC - $450

Standard wheel - $200

Contact me via PM.

Hey peoples,

R34 GTT Power FC with commander for sale - $1500 FIRM - We all know how rare they are!

Blitz R34 GTT Injectors - From memory they are 525CC - $450

Standard wheel - $200

Contact me via PM.

how old are the injectors and have they had much use? will they flow 300kwatw?

Model from From PSI parts website, it uses the old 1cc for 1horsepower rule... you want 300rwkw so..

Working out injector size to support your RWkW Goal

Injector Size (cc) = A / (B x C x D)

A = Projected RWkW Figure

B = 0.8 (80% of Maximum Duty Cycle)

C = 0.85 (Typical 85% of flywheel power is transferred to the wheels)

D = 0.746 (Convert HP to RWKw)

  1. Injector Size (cc) = 300 / (0.8 x 0.85 x 0.746)
  2. Injector Size (cc) = 300 / 0.507
  3. Injector Size (cc) = 591
  4. Injector Size (cc) ≈ 600? (Always round up to next size available)

Note: This calculation only works for Unleaded Fuel, if you are planning to run E85 you should factor in around 30% increase in flow.

Short answer is i think youll need aftermarket injectors for 300rwkw. IF you wanted to push it and included a fuel reg you may get there but i would give yourself room to breathe and peace of mind and go larger rather than smaller on injectors..

how old are the injectors and have they had much use? will they flow 300kwatw?

Yes will push 300+ rwkw. I was powering to 280 at 70% - Not quite sure if sean thinks these are stock but they are aftermarket?! what is he on about?!

Yes car not so straight any more, sad but its either step to a FD or GTR. Not such a bad thing I guess.

Edited by DECIM8

Wheel condition pretty shabby, if you want it for Road worthyness or etc it will be fine, not going to look awesome on though. Saying that its just got cracks from sun exposure.

ADDING o2 sensor (NISSAN ORIGINAL) Used for 100km (F^#^%$K!!! - they cost $250!) Selling for $150.

No cutting wires crap just plug and play!

Edited by DECIM8

whoa dont get me wrong, i was jsut posting up that thing i found on psi parts website so that chris could see how some people would work out what injectors he would need in the future. and i wrote that he would need aftermarket injectors, i think he should buy yours! 525c is a great size for direct fit upgrade. i got nismo 555s and they dont even go close to duty cycle in the 250-300kw range.. blitz 525s would be great for his goal imo

MFD SOLD

Injectors still avaliable - Had people ask to wait till christmas is over but no dosh so up for sale again.

O2 sensor still avaliable

Power FC now $1250

MAF - Now $250

Standard R34 Wheel $100

All parts able to be sent. With insurance and express.

Edited by DECIM8

Injectors on hold.

Power FC now $1200 - Lowest it will get. Its a access autoworks on too! And has the controller whats wrong with you people? next it goes on ebay.

Z32 mass air flow meter now - $200

Edited by DECIM8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...