Jump to content
SAU Community

Recommended Posts

  • Replies 169
  • Created
  • Last Reply

Top Posters In This Topic

Hey guys, lookn forward to the cruze tomorrow as it will be my 1st one.. Only one stupid, really stupid question though, wouldn't it be awkward if I rock up and not know any1? Cuz I was planning to bring some ppl around but they cancelled because they'd rather go to the beach.. Anywayz

i dont know how to get a pic from google maps up here so here is is in text.

Corner of Well's Road/ SPringvale road.

BIG car wash. if someone has the power and skill to get a pic would save alot of confusion. i was going to steal it from an old meet, but the events has been cleaned up real good.

As requested, refer below for map.

P.S - Did I see your Stagea parked behind Costello's in Chelsea around lunchtime yesterday? If so, very clean!

map.jpg

here's a link to the Carwash

http://maps.google.com.au/maps?f=q&sou...817099911895636

and a link to the shop

http://maps.google.com.au/maps?f=q&sou...mp;t=h&z=17

Might be easier to use them link so you can get directions from wherever you're driving from

P.S - Did I see your Stagea parked behind Costello's in Chelsea around lunchtime yesterday? If so, very clean!

I seen that one as well i rode past it on my bike and a good look then i left the car park and a r31 was sitting there.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...