Jump to content
SAU Community

Recommended Posts

I think the redline you want to be running will have more bearing on upgrading the springs, as the stock lift for RB20DET is 7.8mm, so 8.5 isnt a huge increase (RB26 use just over 8.5mm lift).

EDIT: just had a look at the link, as the cams are made for hydrualic lifters, you should be fine as long as you keep the redline sane. I have heard it recommended by the co-owner of Signal (owner's brother) that the RB20DET should not be taken past 8200redline in stock form, with possibly more agressive ramp from the Tomei cams, perhaps even that is a bit too high?

Out of interest, why are you going 270?

Link to comment
https://www.sau.com.au/forums/topic/30132-tomei-270cams/#findComment-612565
Share on other sites

I think the redline you want to be running will have more bearing on upgrading the springs, as the stock lift for RB20DET is 7.8mm, so 8.5 isnt a huge increase (RB26 use just over 8.5mm lift).

EDIT: just had a look at the link, as the cams are made for hydrualic lifters, you should be fine as long as you keep the redline sane.  I have heard it recommended by the co-owner of Signal (owner's brother) that the RB20DET should not be taken past 8200redline in stock form, with possibly more agressive ramp from the Tomei cams, perhaps even that is a bit too high?  

Out of interest, why are you going 270?

I'm goin to be installing a big turbo like a 62-1,60-1 something around that line. I'm more intrested in moving the power band to the higher rpm since it's a 2.0 any way.

Link to comment
https://www.sau.com.au/forums/topic/30132-tomei-270cams/#findComment-612578
Share on other sites

Hi BlueRB240, I agree with Steve, RB20DET valve springs are getting on a bit now. I would upgrade them, which you can do without removing the head. I haven't personally tried it, but I understand that RB26DETT valve springs fit. They could be a relatively easy and cheap upgrade.

Hope that helps

Link to comment
https://www.sau.com.au/forums/topic/30132-tomei-270cams/#findComment-612582
Share on other sites

Hi BlueRB240, I agree with Steve, RB20DET valve springs are getting on a bit now.  I would upgrade them, which you can do without removing the head. I haven't personally tried it, but I understand that RB26DETT valve springs fit.  They could be a relatively easy and cheap upgrade.

Hope that helps

Thanks for the info guys.

Link to comment
https://www.sau.com.au/forums/topic/30132-tomei-270cams/#findComment-612601
Share on other sites

So what would be a good setup with a stock RB20DET, i.e. what lift, duration would you use (what cams, i was thinking HKS step 1 264 for both in and out) and would it be necessary to upgrade the valve springs with these cams? Can you go to step 2 on stock valve springs (i didnt think it was advisable)

Also why do some people use 256 in and 264 out?

Link to comment
https://www.sau.com.au/forums/topic/30132-tomei-270cams/#findComment-612977
Share on other sites

The smaller inlet cam duration gives you that little bit more bottom end torque without affecting the top end to much.

Maybe some thing is wrong with mine as I'd hate to be taking off from a set of lights with the AC on a 30+degree day with a set of large cams in the RB20DET.

Is it mine or are all RB20DET's as gutless as hell until they get a bit of boost in to them?

Link to comment
https://www.sau.com.au/forums/topic/30132-tomei-270cams/#findComment-613362
Share on other sites

Hi Joel, it's just your car. Well, maybe how it is set up and tuned, we run a lot of ignition timing, split dump, electric fan, balance the injectors and spend a fair bit of time tuning our RB20DET off boost and at partial throttle openings with a Power FC. Doing those things I achieved a 100% increase in power at 2,000 rpm. Most tuners go for the highest maximum horsepower and worry only a little bit about average power over the boosted rpm range. And care even less about off boost performance.

Lighter flywheel and road wheels makes a goodly difference as well.

Hope that helps

Merry Xmas

Link to comment
https://www.sau.com.au/forums/topic/30132-tomei-270cams/#findComment-613572
Share on other sites

Hi Joel, it's just your car.  Well, maybe how it is set up and tuned, we run a lot of ignition timing, split dump, electric fan, balance the injectors and spend a fair bit of time tuning our RB20DET off boost and at partial throttle openings with a Power FC.  Doing those things I achieved a 100% increase in power at 2,000 rpm.  Most tuners go for the highest maximum horsepower and worry only a little bit about average power over the boosted rpm range.  And care even less about off boost performance.

Lighter flywheel and road wheels makes a goodly difference as well.

Hope that helps

Merry Xmas

PowerFC for the RB20? Where can I get one? I'm still waiting for my friend from Apexi (USA) to let me know if they make it or is it someone else? still haven't got any word.

Link to comment
https://www.sau.com.au/forums/topic/30132-tomei-270cams/#findComment-613715
Share on other sites

I have been waiting to see if they got the RB25,20 out but still nothing yet. :( looks like it's a commander I'll be using.

Oh.......

Doesn't everyone have an RB26??? ;):D

Just kidding mate :D... Best way to get them to make an RB25 one is to get lots of people emailing them requesting one!!!

Link to comment
https://www.sau.com.au/forums/topic/30132-tomei-270cams/#findComment-614106
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...