Jump to content
SAU Community

Recommended Posts

  • Replies 102
  • Created
  • Last Reply

Top Posters In This Topic

hey man,

im after the drivers window switch thingo...

this:

th_27122009002.jpg

if you still have it. how much + postage to ACT 2602?

Thanks

$50 ill chek up on postage tomorow

hey mate have you still got the right head light ?

ill take it if you still have it. 0416840060

yes i still got it

Hey there, I am after the climate control unit. How much incl postage to Beldon WA. Might be interested in other parts if price is right.

Cheers

hay mate, sorry climate control unit is sold, tell me what you need, we can make the price right.

Hi, mate. How much are you chasing for the Front 4-Spot Calipers?

hay mate, im selling whole 5stud converion for $1200

hubs, rotors, calpiers, all suspension components, the whole lot. front and rear

hay mate, im selling whole 5stud converion for $1200

hubs, rotors, calpiers, all suspension components, the whole lot. front and rear

Ok, so not willing to seperate, then? Just need to front calipers for a project.

Ok, so not willing to seperate, then? Just need to front calipers for a project.

nah man, sorry, i want to sell complete

hmm...well, assuming its not broken (unlike mine :D ) that sounds pretty good.

Thanks

haha, nah mine is in mint condition, not craked

awesome, could you chuck up/pm me a pic of it? no offense, i just want some proof that there's no damage before i buy. :D

yer sweet, ill take pic tomorow, its still on the car

hi

im after the complete set of front left and right guard liners and all clips

how much delievered to sydney

thanks

what are guard liners, you got pic?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...