Jump to content
SAU Community

Recommended Posts

////Alpine V12 amplifier, 4 channel, solid build quality $300 melbourne pickup

////Alpine type R 1242 dual voice coil 12" sub, 4 ohms. $250 melbourne pickup (too heavy to post)

Custom 12" single sub box specially molded to fit right side of R34 GTT or GTR boot, gold banana jack terminals, new $100

[email protected]

post-a262247-.jpg

post-a262248-.jpg

Link to comment
https://www.sau.com.au/forums/topic/301582-alpine-car-audio-r34-12-sub-box/
Share on other sites

The amp is a MRV-F345 - specs can be found here : http://www.crutchfield.com/p_500MRVF345/Al...tures_and_specs

The MRV-F345 4-channel amp produces 75 watts RMS per channel — perfect for driving most component systems or high-quality coaxial speakers. The clean power output allows the speakers to produce the fine detail and nuance that'll separate your system from the rest of the pack. In bridged mode, the versatile MRV-F345 delivers 300 watts from channels 3 and 4 (perfect for running a sub), while you can use channels 1 and 2 to drive the front speakers.

Performance

RMS Power Output (Watts x Channels) 75 x 4

Peak Power Output (Watts x Channels) N/A

Power at 2 Ohms (Watts x Channels) 150 x 4

Bridged Power (Watts x Channels) 300 x 1

Minimum Impedance Bridged 4

Minimum Impedance Unbridged 2

Best Frequency Response 10-50k Hz

THD at Rated RMS Power 0.3%

Signal to Noise Ratio 73 dB

Input Voltage 14.4v

Features

Amplifier Class AB

Low-Pass Crossover Frequency 30-400Hz/600-8kHz

Low-Pass Slope (dB/octave) 12 dB

High-Pass Crossover Frequency 30-400Hz/600-8kHz

High-Pass Slope (dB/octave) 12 dB

Bass Boost 0-16 dB

Bass Boost Frequency 45

Fan Cooled Yes

Fuse Rating 30 x 2

Speaker Level Inputs No

Preamp Outputs 1 pair

LED Power Indicator Blue

Width (inches) 13

Height (inches) 2-7/16

Depth (inches) 9

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...