Jump to content
SAU Community

Recommended Posts

////Alpine V12 amplifier, 4 channel, solid build quality $300 melbourne pickup

////Alpine type R 1242 dual voice coil 12" sub, 4 ohms. $250 melbourne pickup (too heavy to post)

Custom 12" single sub box specially molded to fit right side of R34 GTT or GTR boot, gold banana jack terminals, new $100

[email protected]

post-a262247-.jpg

post-a262248-.jpg

Link to comment
https://www.sau.com.au/forums/topic/301582-alpine-car-audio-r34-12-sub-box/
Share on other sites

The amp is a MRV-F345 - specs can be found here : http://www.crutchfield.com/p_500MRVF345/Al...tures_and_specs

The MRV-F345 4-channel amp produces 75 watts RMS per channel — perfect for driving most component systems or high-quality coaxial speakers. The clean power output allows the speakers to produce the fine detail and nuance that'll separate your system from the rest of the pack. In bridged mode, the versatile MRV-F345 delivers 300 watts from channels 3 and 4 (perfect for running a sub), while you can use channels 1 and 2 to drive the front speakers.

Performance

RMS Power Output (Watts x Channels) 75 x 4

Peak Power Output (Watts x Channels) N/A

Power at 2 Ohms (Watts x Channels) 150 x 4

Bridged Power (Watts x Channels) 300 x 1

Minimum Impedance Bridged 4

Minimum Impedance Unbridged 2

Best Frequency Response 10-50k Hz

THD at Rated RMS Power 0.3%

Signal to Noise Ratio 73 dB

Input Voltage 14.4v

Features

Amplifier Class AB

Low-Pass Crossover Frequency 30-400Hz/600-8kHz

Low-Pass Slope (dB/octave) 12 dB

High-Pass Crossover Frequency 30-400Hz/600-8kHz

High-Pass Slope (dB/octave) 12 dB

Bass Boost 0-16 dB

Bass Boost Frequency 45

Fan Cooled Yes

Fuse Rating 30 x 2

Speaker Level Inputs No

Preamp Outputs 1 pair

LED Power Indicator Blue

Width (inches) 13

Height (inches) 2-7/16

Depth (inches) 9

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...