Jump to content
SAU Community

Recommended Posts

Item Summary: Nissan Skyline R31 GTS-X Coupe - 1986 R31 Coupe - VG30DET Conversion!

Location: QLD: Brisbane

Condition: Used

Reason for Selling: Lost Interest

Asking Price: 10500

Delivery Methods: PickUp

Contact Info: PM Me for additional info

Extra Information:

Hi All,

I no longer have space or time to continue this project.

The following are the specs and information on what has been done.

PERFORMANCE MODIFICATIONS

*VG30DET - (STANDARD flywheel figure as quoted by Nissan Japan = 190kw @ 6000rpm & 343NM @ 3200rpm - using no intercooler)

*Custom heavy-duty engine mounts to suit

*VG30DETT 5 speed - Z32 300ZX, VERY strong gearbox, similar to R33 RB25DET gearbox internally

*Exedy Single Plate Brass Button Clutch

*Custom balanced 2-piece tailshaft for high RPM/High Speed durability

*APC (Advanced Performance Centre @ Underwood) Replacement intercooler - good for 600HP

*ALL aluminium inlet and intercooler pipework - heaps lighter than stainless or mild steel

*New K&N Pod Filter

*Upgraded 550cc O-Ring Injectors on custom rails

*-6 Billet fuel pressure regulator

*Polished Alloy Oil/Air Separator

*New R31 Aussie delivered radiator

*AU Falcon Thermo Fan Assembly

*4" into 3" turbo dump pipe

*3" exhaust system with high flow cat

*Reconditioned Steering Rack

*5 Stud conversion

*Nissan 4 Spot Front Calipers R32

*Nissan 2 Spot Rear Calipers R32

*Pedders "Sports Rider Suspension & Springs"

*Haltech E6X ECU - Fully wired and neatly installed

*GM LS1 Coil Pack + Leads

*GReddy Turbo Timer

****************ALL THE ABOVE IS MOD PLATED *****************

INTERIOR MODIFICATIONS

*Trust Gear knob

*Sony CDX-M800 Head unit

* JL Audio 6.5" splits (front)

*JL Audio 6"x9" (rear)

*VDO Oil, Water, Shift Lights

*Autometer Boost Gauge

EXTERIOR MODIFICATIONS

*Parabola Headlights

*Front Bar Modified to suit FMIC

*R32 GTR 16" x 8" rear rims painted in RAYS Engineering Bronze

*R32 GTS-T 16" x 6.5" rims painted in RAYS Engineering Bronze

Asking Price $10,500 ono - No swaps please.

For more info PM me.

IMG_0129Large.jpg

IMG_0126Large.jpg

IMG_0125Large.jpg

IMG_0124Large.jpg

IMG_0115Large.jpg

IMG_0114Large.jpg

IMG_0109Large.jpg

Tim

Link to comment
https://www.sau.com.au/forums/topic/301924-nissan-skyline-r31-gts-x-coupe-1986/
Share on other sites

  • 4 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 1 month later...
  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...