Jump to content
SAU Community

Alignment Issue

Shanu

By Shanu,
in Victoria

 Share

Recommended Posts

Shanu Collaborator

Shanu

Posted
Posted (edited)

hey guys,have a question regarding car going to the right when accelerating hard.not the skyline i bought chaser yesterday didnt drive

that much took it for a spin today the alignment out a bit as the car goes to the left when u leave the steering,but the thing am worried about

is when i accelerate the car hard its pulls to the right and have to hold the steering as soon a i lift the foot back to the left(straight) but when am driving slow (cruising ) no issues.it pulls to the right when i accelerate hard.everything was closed today so didnt do the alignment.the question is will a wheel alignment fix the problem or could it be something serious? help would be appreciated

Edited by Shanu
Link to comment
https://www.sau.com.au/forums/topic/302127-alignment-issue/
Share on other sites
Shanu Collaborator

Shanu

Posted
  • Author
Posted
Check wheek nuts, check tyre pressures, get under the car and check condition of all bushes/ball joints(or get this done with alignment), Get alignment, Check ride height, What diff and tyres?

235/18/40 rear, 225/18/40 front.its the standard LSD comes from factory,ride height that i have to check cuz the guy who i got it off had to rais it to get it registered.no noises or anything from the diff could there be a problem there ?

Link to comment
https://www.sau.com.au/forums/topic/302127-alignment-issue/#findComment-5012042
Share on other sites
_Ryan_ Grand Master

_Ryan_

Posted
Posted
235/18/40 rear, 225/18/40 front.its the standard LSD comes from factory,ride height that i have to check cuz the guy who i got it off had to rais it to get it registered.no noises or anything from the diff could there be a problem there ?

I more meant are tyres equal tread on each axle.

Was it aligned after the ride height change?

Check bushes/ball joints/alignment/Tyre pres.

Link to comment
https://www.sau.com.au/forums/topic/302127-alignment-issue/#findComment-5012059
Share on other sites
Shanu Collaborator

Shanu

Posted
  • Author
Posted
I more meant are tyres equal tread on each axle.

Was it aligned after the ride height change?

Check bushes/ball joints/alignment/Tyre pres.

yep tread is equal all around,nope didnt do any alignment,will check the stuff that u mentioned.thanx for the advice mate :woot:

Link to comment
https://www.sau.com.au/forums/topic/302127-alignment-issue/#findComment-5012074
Share on other sites
KURAUN Grand Master

KURAUN

Posted
Posted
235/18/40 rear, 225/18/40 front.its the standard LSD comes from factory,ride height that i have to check cuz the guy who i got it off had to rais it to get it registered.no noises or anything from the diff could there be a problem there ?

sounds like alignment cause the guy raised it to get it registered he probably didnt have it realigned

Link to comment
https://www.sau.com.au/forums/topic/302127-alignment-issue/#findComment-5013021
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Who has a Infiniti Q60, Q50 (V37)?

      By Duncan · Posted

      The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • MBS206
      Who has a Infiniti Q60, Q50 (V37)?

      By MBS206 · Posted

      Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...