Jump to content
SAU Community

Recommended Posts

CAR IS BACK UP 4 GRABS PPL!

Wanting more of a daily driver as this r33 is far from stock, $15,000ono or swap depending on wat u got so show me wat ya got cheers clayton Pm or call 0404 232 231

FORGIED WISECO PISTONS (BALANCED, BEARINGS, ETC)

GTR RODS

TRUST 1.6L HEAD GASKET

GARRETT(500HP) GT30/40 SITTING ON HIGHT MOUNT MANIFOLD

PORT POLISH HEAD ECT

48MM TURBOSMART PRO EXTERNAL WASTE GATE

FULL 3 1/2INCH EXHAUST

APEXI POWER FC WITH HAND SET

APEXI BOOST CONTROLER

GREDDY OIL FILTER RELOCATION KIT

HYBRID FRONT MOUNT INTERCOOLER

720CC INJECTORS+FUEL REG

500HP FUEL PUMP

Z32 AIR FLOW METER

STRONG GEARBOX CUSTOM CLUTCH RATED AT 400HP

GFB BLOW OFF VALVE

APEXI ADJUSTABLE DAMPER COILOVERS

FRONT STRUT BRACE

SLOTTED FRONT ROTORS

FULLY 400R BODY KIT

ALPINE TV/DVD/MP3 PLAYER

KENWOOD 600RMS SUB AMD AMP (TOP OF THE RANGE SUB)

FUSION FRONT SLPITS AND 6X9 REARS

NISMO GEAR NOB

18INCH DEEP DISH STARCORPS WHEELS BRAND NEW TYTRES

ii002.jpgw2048.png

ii008.jpgw2048.png

ii052.jpgw2048.png

ii116.jpgw2048.png

ii129.jpgw2048.png

Edited by Zoidberg
Link to comment
https://www.sau.com.au/forums/topic/302948-300rwkw-skyline-4-sale-or-swap/
Share on other sites

pics are available at myspace.com/scott_to4

1996 VS HSV MANTA, V8 auto, car is black in colour, panther mica metallic. Chrome calais exterior window trims, chrome 19 inch rims, lowered, 4 point camber kit in rear suspension, immaculate original hsv interior, %5 window tint, lowered, pacemaker extractors, full twin 3 inch exhaust, sony cd player, awesome cruiser. body and paint in awesome condition, only down points are it has a power steering leak and needs a few bushes in the front end. im located in central coast nsw, where abouts are you?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...