Jump to content
SAU Community

Recommended Posts

Hi guys,

I have up for sale a set of 18" Nismo lmgt4 rims.

$3400 firm

Fronts:

8.5 width

+25 offset

245/40 tyres

post-61036-1263081917_thumb.jpgpost-61036-1263081950_thumb.jpgpost-61036-1263081984_thumb.jpgpost-61036-1263082020_thumb.jpg

Rears:

9.5 width

+30 offset

275/40 tyres

post-61036-1263082175_thumb.jpgpost-61036-1263082233_thumb.jpgpost-61036-1263082058_thumb.jpgpost-61036-1263082266_thumb.jpgpost-61036-1263082133_thumb.jpg

Some minor gutter rash on 2 of the wheels and general scratches/nicks around the nut holes.

I have an r32 gts-t and the fronts would have required 225/40 tyres to clear the upper control arms. The rears stick out about 2cm past the guards and would have needed rolling/ flaring to fit under properly. I liked the drift look but just too hard finding people in Bendigo to help set my skyline up (Commonwhore capital here). So I ended up finding a set of the 17" and putting them on instead.

You can text me during the day or call after 6pm on 0409 503 290 or pm.

Kye

Link to comment
https://www.sau.com.au/forums/topic/303196-18-nismo-lmgt4-rims/
Share on other sites

Original and quality rims like these arent going to be cheap. Look up how much these are on the net and you'll see what I mean. Good luck finding a set of lmgt4s in your price range then :)

3.4k for used lmgt4's is a bit steep in those sizes seeing as though Nengun are selling 18x10.5 with better offsets for a little over 3k

I did see them on Nengun. But put in some details and see how much freight is :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...