Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...
  • Replies 124
  • Created
  • Last Reply

Top Posters In This Topic

hey mate would sard side feed injectors fit straight into this setup? pretty sure they are 800cc if that makes a difference.

hey mate would sard side feed injectors fit straight into this setup? pretty sure they are 800cc if that makes a difference.

Hey,

It's intended to be used with your original fuel rail set-up.

- Brendan

  • 3 weeks later...

Hey mate, pretty keen. Got on that web link and couldn't find the plenums on there anywhere? anyway can i get pictures of plain cast and polished finish, and do these kits come with fuel rails also or are they extra? Cheers

Hey mate, pretty keen. Got on that web link and couldn't find the plenums on there anywhere? anyway can i get pictures of plain cast and polished finish, and do these kits come with fuel rails also or are they extra? Cheers

Hey,

What link are you referring to?

I'll PM you a picture off the cast and chrome versions, this is just for the plenum but if you require the fuel rail as well it would only be $95.

- Brendan

hey mate could you PM me the price for polished plenum, 80mm TB and postage to 7015 thanks :)

Beau you have been PM'ed :yes:

  • 2 months later...

988629_10151523523274440_1554117959_n.jp

New intake plenum installed!! thanks to Vulture motorsport selling this one to me! was a perfect fit with my 850cc sard injectors :)

  • 3 weeks later...

hey mate do u sell the throttle adaptor plate seperately?? cheers

Hey!

Yes we do have them in stock - $100 delivered.

That comes with a back-plate and fittings.

- Brendan

  • 2 months later...
  • 2 months later...

Quick mention - these are also available in a 'raw' cast finish for those looking at painting them :yes:

Gday mate, what price do you have on the raw finish with larger throttle body and fuel rail. Posted to 2173?

Does the kit include everything needed to fit it to the motor and have it working correctly or will i need to buy any fittings or hoses etc?

Cheers

  • 2 weeks later...

Gday mate, what price do you have on the raw finish with larger throttle body and fuel rail. Posted to 2173?

Does the kit include everything needed to fit it to the motor and have it working correctly or will i need to buy any fittings or hoses etc?

Cheers

PM Sent mate.

Gday mate, what price do you have on the raw finish with larger throttle body and fuel rail. Posted to 2173?

Does the kit include everything needed to fit it to the motor and have it working correctly or will i need to buy any fittings or hoses etc?

Cheers

Thanks for that mate, didnt get the Pm though? Would like to get one ordered soon!




  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...