Jump to content
SAU Community

Recommended Posts

Oh SH#TTTT my car is overheating........

Ok ere's the story 1 - car accident

2 - car repaired

3 - got 2nd hand radiator

4 - rad flush to the best I could

5 - radiator fitted

6 - filled coolant

7 - started car drove for 15 minute gauge needle on top hhhhhhhot

8 - overheating, top radiator hose boillling

9 - however bottom rad hose cold as

so I don't know what it is can someone help. Now I rather try to get help and not to pay a fortune, my thoughts are thermostat failed blocking waterflow, fan not spinging, water pump seized (but no unusual noise), radiator blocked water can''t circulate hmmmmmm. I want my baby on the road finally had enough of it just getting towed from one place to another fudge

Anyway feedback would be great cheer

Link to comment
https://www.sau.com.au/forums/topic/303491-help-help-help/
Share on other sites

2 things..

Most likely the thermostats stuck(you can take it out and run and see if it makes a diff) or the radiators blocked up BAD..

My advice - take the thermostat out and tkae it for a drive.. it will take a bit longer to heat up.. after the drive, BOTH the radiator pipes should be almost the same temp.. if not then u have a blocked radiator for sure.

EDIT - You might also have a BIG airlock - did you bleed your cooling system? If not, do so as well.

Edited by Ultimategtr
Link to comment
https://www.sau.com.au/forums/topic/303491-help-help-help/#findComment-5029262
Share on other sites

Well you have pretty much said most of the problems that I can think of that would cause a car to overheat, now its just time to narrow it down.

Depending on the condition (km's) of your car, I wouldnt think the water pump seized. When I needed to get a new one, the seals failed and coolant leaked everywhere. Do you have any leaks from the cooling system? From the water pump? Radiator, hoses etc? Run the car on idle and see if there are any leaks.

Thermostats do fail and there not overly expensive so I would probably changed that first and see what happens. Then I would question the 2nd hand radiator.

Link to comment
https://www.sau.com.au/forums/topic/303491-help-help-help/#findComment-5029279
Share on other sites

i'm guessing that this only started after the accident and not before hand?

if so, i'd be getting the radiator professionally cleaned first. that is more than likely going to be the problem as it was the only thing replaced. however i would also be checking the clutch fan as that may also have been damaged in the crash. but since the lower hose is cold i'd be guessing it's the core being blocked, which normal radiator flushing does vey little to fix.

Link to comment
https://www.sau.com.au/forums/topic/303491-help-help-help/#findComment-5029589
Share on other sites

Cool, thanks for the feedback all I'll get on to it starting off with thermostat and bleeding the air, afterwards it will be upgrade to an ally radiator and finally if that dont do it waterpump and if that aint workn, :) time to take out the grinder.........

]thanks again......LONG LIVE SAU.............................................................................

...............

Link to comment
https://www.sau.com.au/forums/topic/303491-help-help-help/#findComment-5029846
Share on other sites

I'm not sure about how old it is I purchased it damaged (minor) however I'm replacing the radiator anyway this week to an ally I've taken off the heater hose but no water seems to be going there at all. I have a gready inlet manifold on the beast so the thermostats hard to get to so will have to wait for mechanic. to sort it.

hm radiator cap will replace that too thnxxxx all

LONG LIVE SAU

Link to comment
https://www.sau.com.au/forums/topic/303491-help-help-help/#findComment-5031295
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...