Jump to content
SAU Community

Recommended Posts

Ok all for sale.

pics here http://motamota.r31skylineclub.com/index.php?topic=122545.0

16x7 +25 16x8+25 wantanbee rims one is scratched on the inside $1100

all tyers are just above RWC, the rim that is scratched has some chunks taken out of the tread but should be fine, will conferm. any 4 stud car (with in reason)

bosh 040 fuel pump in cradel (is brand new and has not run more then 1 hour) $300 unversal

exstractors, were on the car when i got it $250. R13

2.5" cat back exhasut I think it is mandral bent ill conferm when it come's off it also has two mufflers but when you rev it sounds reay nice. Price to be confermed be around $300 R31

king springs low with munro shocks (no leaks) $400 didn't notice any problems when i drove the 3km. R31

sloted front discs they seem to be fine no major lips dont know what brand $100 R31

manual convertion with nismo leather gear lever. RB30E box

also has brand new clutch (i think it's BPR) it's done 3km.

box work's fine no noise or grinding.

the gear lever was cut down when i brought and have glued the gear lever on the stick. so you will also get a blue suround and the rubber boot is brand new.

s13 hubs and LCA $300

cusco zero 2 coilovers 8kg/mm fronts rears are cusco base models.

non base height adjustble non damper adjustable $800 S13

hot plate tail lights in very good condition $100 or can sell as a convertion for s1/2 cars for $150. R31

electric areal that works $20 R31

elec mirrors that work name a price R31

s3 front end convertion R31 (if any body wonts it) name a decent price and it's your's

moded air box (removed the bell mouth) R31 skyline $10

KA24 TB with match ported inlet on RB30E $150

interior minus front seats (is silo styled but in bue) ill get some pic's and name a price. R31 skyline

nistune ecu for n/a eng RB30E (in R31) $200

pm me or call 0411895116

Items are in darwin so will have to freight/post i can orgonise this at buyers exspence.

will need your post code to work out freight.

If you do need any other parts from a GXE S3 let me know as im parting it.

post-32868-1263277298_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/303582-darwin-various-parts/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
×
×
  • Create New...