Jump to content
SAU Community

Clutch Assembly Broken How To Remove?

bad_rb20
 Share

Recommended Posts

bad_rb20 Community Regular

bad_rb20

Posted
Posted

hi all it seems like i've snapped the connection to the plate on the firewall on the clutch assembly on my 32 gtst so the clutch pedal is over the shop so it wont engage. apprently is a common fault. had alook and cant work out how to take the whole plate and clutch assembly out. any instruction/advice or experience would be greatly appreciated. is it normal to just weld it back on?

R33_NICK Community Regular

R33_NICK

Posted
Posted

hey mate, had this happen to me just recently as well tho i was lucky the whole thing didnt come off completely and hold the assembly on with a coat hanger while getting it fixed (dont do this, not recommended but had no choice since its my daily driver). what the problem was, one of your spotwelds on the bracket might have snapped, a common problem if you have a heavy duty clutch or any clutch that has higher clamping force than standard. cheapest solution is to get it rewelded around the spotwelds and add a bit more weld to reinforce it on the way which is what i did. becareful where you weld or the material will get in the way when reinstalling back to the firewall. but if your willing to spend a bit more, the nismo solution as Elite racing mentioned is the best way to go as it doesnt cost much more than da factory one ($110 quoted for standard Nissan).

blind_elk Grand Master

blind_elk

Posted
Posted

The assembly is held in by the same 3 bolts that hold the clutch master cylinder in place, and a bolt up behind the instrument panel (I found it easiest to remove the instrument panel to get at that one).

The Dan Grand Master

The Dan

Posted
Posted

You shouldn't need to remove the instrument panel. A 9-12 inch 3/8 drive extension and 12mm socket should get it quite easily from underneath. You just have to worm it past a couple of wires.

But as said above. That one and the two that hold the clutch master cylinder on and it's away. Leave the pedal in place as it's gonna come out with the rest of it.

I recommend getting the Nismo one as it might save you a couple of dollars to get it welded but I have found that in around 50% of the time the metal will crack again within 12 months right next to where it was welded. It's much better to replace it with the already reinforced one and then forget about it.

The Dan Grand Master

The Dan

Posted
Posted

Contact Link International on 07 3382 5000.

They are in Brisbane. Or I think Unique Auto Sports is the Nismo dealer down south.

Part number for R32 is - N-46550-RS580 Retail price is $148 but depending on who you buy it from, you can get them cheaper. They keep them on the shelf usually.

Chibs Community Regular

Chibs

Posted
Posted

Hey guys,

Think this is whats happened to me... Except i am leaking transmission fluid from under the car... Car starts and i can put it in gear when the car is off but cant when it is turned on.... Its parked under my workplace and i need to get it out! any temp fix to get it moving back home?

I have turned the car off put it in gear then tried to turn it back on but it wouldnt turn on

Any help is appreciated

Cheers!

The Dan Grand Master

The Dan

Posted
Posted
Hey guys,

Think this is whats happened to me... Except i am leaking transmission fluid from under the car... Car starts and i can put it in gear when the car is off but cant when it is turned on.... Its parked under my workplace and i need to get it out! any temp fix to get it moving back home?

I have turned the car off put it in gear then tried to turn it back on but it wouldnt turn on

Any help is appreciated

Cheers!

Yes, you need to replace the clutch slave cylinder and/or the master cylinder. Considering there is fluid under the car, I would start with the slave cylinder.

Ring Nissan and buy it genuine. They cost around $100 for the R33 one. Dunno what the 32 one costs.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      S1 rb25/s14 starting problem

      By Dose Pipe Sutututu · Posted

      When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...