Jump to content
SAU Community

Recommended Posts

TEIN Racing Spec Type-RA

Bought these for my 34 GT but they do not fit

These coilovers were set up for Nissan Skyline GT-R R33 (BCNR33) but will also fit R33 GTS-4 model and should go into R32 and R34 GT-R without too much trouble. You can see from the photos that the condition is outstanding for used suspension. They were obviously not fitted to a car for very long so they are almost as good as new.

For sale is exactly what you see in the photos including coilover shocks, strut tops, bump stops, dust covers, mounting bolts, adjustable spring mounts, damper adjusters, etc (there are no springs included with this set)

post-47337-1263878378_thumb.jpg post-47337-1263878417_thumb.jpg

post-47337-1263878446_thumb.jpg post-47337-1263878468_thumb.jpg

post-47337-1263878487_thumb.jpg

$600 will post at buyers expense items located in Adelaide

Contact via pm or phone on 0433348748

info on tein RA as posted on website

  • Type RA TEIN suspension has adapted into its package, the specifications used in the rally field such as the World Rally Championship. TEIN has constructed a footwork for you which gives priority to function.
  • A high grade specification which gives you an unsurpassed drive feel.
  • Introduction of specifications used at competition levels.
  • Adopted a single rod structure for better reception between driver and road surface.
  • A linear damping effect which adapts to even the smallest road surface abnormality by adapting the single rod structure.
  • Seamless tube using a drawing method. Processing technology which enables a high level of precision up to 1/100mm of the inner diameter. Inner surface precision up to 3.2S (inner surface bumps within +/- 1.6 micrometer)
  • Use of ultra light and strong aluminum - A7050 which is also used in airplanes.
  • A I.D.45 piston which is maximum for marketed cars' shock absorber.
  • A different diameter multi-level valve structure which enables damping effect and specifications adjustment.
  • The damping effect adjustment structure uses an evolved version of the special shaped needle valve which has already been proven in the HA/NA dampers.
Link to comment
https://www.sau.com.au/forums/topic/304550-tein-ra-coilovers-32-33-gtr/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...