Jump to content
SAU Community

Rb30/ Rb34

Davyboy

By Davyboy,
in Western Australia

 Share

Recommended Posts

Davyboy Enthusiast

Davyboy

Posted
Posted

Hey guys im about to embark on an engine build for my R33 GTS-T

The engine will be a RB30 block, with an RB26 head with twin turbos.

i was looking on the net and came across a website that sells a 3.4L stroker kit for an RB30

I was wondering if putting that in would be much of a gain? iv searched the forum and cant find anyone that has done it.

It would give me more displacement and torque obviously, but i guess that would also cut the ability to rev down as well

Would it be worth it?

cheers

Link to comment
https://www.sau.com.au/forums/topic/305589-rb30-rb34/
Share on other sites
bubba Grand Master

bubba

Posted
Posted (edited)

Davy, I highly suggest thoroughly reading the RB30 subsection of the Forced Induction forum.

If you have any questions after that, then post up or PM me. Haven't done a 30 with a 26 head but we've built them with 25DE and 25DET heads so will advise where I can :(

And yes, Spool Imports will be making the 3.4L stroker kits. I believe he has two set of pistons and cranks ready to go in test engines, I wouldn't be holding my breath as to when they're available though. Which in that case, if you really do want to go RB34 at some point, maybe a stock rebuilt (freshened up) bottom end is the way to go until the 3.4L kits are released.

Edited by bubba
Link to comment
https://www.sau.com.au/forums/topic/305589-rb30-rb34/#findComment-5055710
Share on other sites
Davyboy Enthusiast

Davyboy

Posted
  • Author
Posted

cheers for that i wasnt aware that it was only a test package lol

bubba: i have read the subforum. from what i understand the 26 head will bold straight up, just needs a little modification, but not as much as the 25. i will probably be in touch when i start the build :down:

Link to comment
https://www.sau.com.au/forums/topic/305589-rb30-rb34/#findComment-5057115
Share on other sites
carbonjunky Apprentice

carbonjunky

Posted
Posted

hey davyboy, im looking to do a similar build your doing, 3.4 stroker with a single to4z, ive got a few parts together already and im hanging out to see how this kit performs.

ive heard about spool doing a 3.4 stroker kit but a friend has told me that a comapny called nitto performance engineering are doing a sroker kit aswell but there are no details on their website yet.

Link to comment
https://www.sau.com.au/forums/topic/305589-rb30-rb34/#findComment-5062449
Share on other sites
  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...