Jump to content
SAU Community

Recommended Posts

R32/R33 GTR Power FC and Hand controller = $699

Passengar S13 silvia door (blue) = $50

Trust power evolution II cat back and de-cat pipe for R32 = $599 ono

Sard Fuel Pressure Reg (used) = $99

Rear strut brace for R32 = $80 ono

Standard S13 silvia steering wheel = $75 ono

Blitz Oil cooler kit with relocator for R32 = $750 ono

SSR Gartimaier wheels 18x9/18x10 +38 (basically new condition) = $1799 ono

SSR Strusse wheels 19x10/19x11 +11 (centre's freshly powder coated black) = $1799 ono

Medusa wheels 18x9/18x10 -10 (centre's freshly powder coated black) = $1799 ono

S13 silvia second hand front ISC N1 coilovers (lessthen 100km old) = $550 ono

CA18det high flowed P/S pump cost $550 selling for = $249 ono

Used adjustable toe arms (2 sets) = $100 ono (each set)

Fixed back seat rails for S13/180sx etc = $100 ono

JIC GTR style reclinable seat (perfect condition) = $499 ono

Buddy Club fixed back seat (brand new) = $699 ono

Nismo 260kmph speedo R32GTR = $299 ono

RB26dett hard pipe intercooler kit = $199 ono

RB26dett generic front pipe (aftermarket) = $150 ono

Greddy Boost gauge (2 available) = $80 ono (each).

Turbosmart EBoost2 40psi 60mm (brand new in box) = $599

***Pictures available on request.

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

will the toe arms fit r34? are they rose joint adjustable? or do they have adjustable bushes?

if they'll fit r34 gtt and are adjustble bushes can i grab some pics?

Cheers

will the toe arms fit r34? are they rose joint adjustable? or do they have adjustable bushes?

if they'll fit r34 gtt and are adjustble bushes can i grab some pics?

Cheers

They will fir R32, S13, 180sx, A31.

The only thing you will need to do to make them fit R33/R34 is to put some spacers in there as the rod end is a few mm smaller. Yes they are rose joint adjustable.

Bek

Hi interested in exhaust, not so much de-cat pipe tho as i have a 3 inch cat. could i have pics of exhaust plz :) also how much would it cost to post to yamba 2464?

Edited by DuFFR32

Pics below (just needs a wipe down). This exhaust cost's around $1499 new from Trust and is 3.75".

Bek

post-5846-1264651990_thumb.jpg

post-5846-1264652007_thumb.jpg

Edited by boostd_r32_gurl

SSR Gartimaier wheels 18x9/18x10 +38 (basically new condition) = $1799 ono

pics pls

Pics below (just needs a wipe down). This exhaust cost's around $1499 new from Trust and is 3.75".

Bek

They are a good bit of gear, have one myself!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...