Jump to content
SAU Community

Recommended Posts

Hi, the battery on my V35 GT* sedan has run flat and I need to get a new one. There is a number on the top of my battery which is "110D26L" though it doesn't seem to match up to any battery models around.

I see on this thread http://www.skylinesaustralia.com/forums/Ba...&hl=Battery that rs73 recommends a BNS60LS or Century NS60LS; however these don't seem to be a direct replacement.

In the same thread I think that superspit recommends a NZ40L from Supercheap and Ben H recommends a NRMA 2384 "Premium".

I searched on the Battery World website which suggests a brads GS Yuasa, Centruy and Maxx with NS40ZLX being the best battery and NS40ZL being listed as a 'performance battery'.

What battery have you used?

Edited by Birth
Link to comment
https://www.sau.com.au/forums/topic/306205-which-battery-for-a-v35-gt8-sedan/
Share on other sites

NS60 series aren't direct replacement they're about 1cm lower than standard. but you can get away either by screwing down the battery clamp lower

or put a 1cm hard foam/rubber layer under the battery to lift it up to correct height.

Not sure about NS40 series

I'm running century NS60LS ...last I checked the NS40 didn't have the same capacity CCA.

and if you have the same connectors as mine, then you'll also need to get the battery with 2 smaller terminal heads coz u can't clamp on to the standard sized ones

fcruz3r, when I look up the Century NS60LS on the Century website at http://www.centurybatteries.com.au/asp/ind...11&type=109 it seems that the NS60LS is a multipost battery. Is that what you have?

post-28712-1265066100_thumb.jpg

Edited by Birth

thats the exact one I have.

400CCA will give you plenty of juice to start the car, only downside is that you will have to loose the red plastic cover on the +ve lead as there's little room to connect the ring clamp to the smaller post

Edited by fcruz3r

You don't have to loose the red plastic cover, it's a good idea to keep it to prevent short circuit if in case it came into contact or getting wet.

Just trim a bit of side wall of the plastic cover where it gets in the way with the larger terminal. Use a strong scissors or a cutting plier.

  • 3 months later...
fcruz3r, when I look up the Century NS60LS on the Century website at http://www.centurybatteries.com.au/asp/ind...11&type=109 it seems that the NS60LS is a multipost battery. Is that what you have?

I was not able to get a multipost battery, so fitted the NS60LS with the big posts and had to buy some battery clamps to fit the bigger posts. Bit of a pain but got there in the end.

  • 1 month later...
  • 8 months later...

My battery shit itself this morning,

was able to push start and i drove straight down to battery world. For $150 i got myself a Century NS60LMF installed which was assured a direct OEM replacement. Had the correct form factor, same dimensions so no need to boost it with a plate as it was too short (mentioned previously), rated at 430CCA and of course full 2 year warranty. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
    • https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
    • There is a guy who said he can weld me piping without having to cut chassis, maybe I do that ? Or do I just go reverse flow but isn’t reverse flow very limited once again? 
×
×
  • Create New...