Jump to content
SAU Community

Shaved Head/block

Don Dada

By Don Dada,
in Engines & Forced Induction

 Share

Recommended Posts

  • 2 weeks later...
winstonusmc Enthusiast

winstonusmc

Posted
Posted

The only tru way is to pull the head off and measure it. You could do a compression test. If the numbers are higher than factory specs, it is shaved. But I know with my shaved head, it pings a little in a low gear and high load, like going up a long hill at 2000 rpm. Is your ECU tuned? If so post up your tune if you know how and I can see if it has been adjusted for higher compression. Of course whoever built your engine could have put a thicker head gasket on to counter the shaved head.

My question is why do you want to know? Are you wanting to shave it again?

T04GTR Grand Master

T04GTR

Posted
Posted

on a rb26, on the underside of the head at the front there is a foil sticker. all virgin heads have them. if its gone then you know its been done. also the factory finnish is very fine. not cause like most machine shops do it.

you would have to get 2 side by side and see.

Don Dada Mentor

Don Dada

Posted
  • Author
Posted
The only tru way is to pull the head off and measure it. You could do a compression test. If the numbers are higher than factory specs, it is shaved. But I know with my shaved head, it pings a little in a low gear and high load, like going up a long hill at 2000 rpm. Is your ECU tuned? If so post up your tune if you know how and I can see if it has been adjusted for higher compression. Of course whoever built your engine could have put a thicker head gasket on to counter the shaved head.

My question is why do you want to know? Are you wanting to shave it again?

You hit he nail on the head!

It does ping on a hot day pulling off in first with the ac on and if i dont give it enough throttle,and comp did come up a little high, with 175 being the highest so all this lead me to believe it was shaved......also using 95oct on the stock ecu.

I guess compression hasn't raised by that much though because Nissan says it suppose to be 170 from factory, so surely 175 shouldn't make much difference.

I got the engine from the importers so god alone knows what the japs did, but i am thinking about putting in some forged pistons, freshen it up a bit and use a metal hg and i know the head has to be perfectly flat to use this so a wanted to know if it can be shaved again if the need be.

I dont have much knowledge in this area and i am not in Aus, and from my experience the builders here are not 100% trust worthy either and i cannot take their word for it, so when u say pull off the head and measure it....what exactly am i measuring???

Basically i just want to know if the head is within tolerance so i need to know if it has been shaved already,if so how much has it been shaved, and can it be safely shaved again

Also, only aftermarket gaskets are metal right??? so i must know if its a stock or aftermarket head gasket in there right now?

Thanks

winstonusmc Enthusiast

winstonusmc

Posted
Posted

You have the option of putting a larger head gasket in to drop the compression back to where it should be. I have a .4 mil shaved head and it raised the compression to 190 across all cylinders. Of course, the rings seem to be in great shape so I would guess .2mil over stock head gasket should get you to a better comp ratio.

Checking a head when you pull it off for warpage should let you know if any more material needs to be removed. If you are OK, then the thicker head gasket should get you back to normal compression. When you pull the head, check the gasket to see if its already a thicker one. If so, you may need to go thicker.

I also have chipped my ECU to almost eliminate the pinging. It pulls the low rpm timing down 5 degrees or so but retains the origional timing at higher rpm. seems to work pretty good so far. If you want the Bin, let me know. I will remove all the injector and MAF scaling to work with a stock engine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...