Jump to content
SAU Community

Recommended Posts

Dead keen on coming to the one in March. Would be good if a few other new track people could come to so I'm not the only new one. Been wanting to get into track days for a long time.

So as far as licencing goes, No Limits will take care of it all once you get there? But what's the go with car requirements? Eg, Do you need a cage, fire extinguisher etc...

get on www.nolimitevents.com join up, go on forums there and ask away....

pretty sure they can still organise your cams license, I'll ask the question and post up the answer soon, you will need 1kg fire extinguisher mounted in the car, long sleeves, halmet etc ---check out site......

and there is also at least 4-5 newbies so you won't be the only one....

Its rare you will be the only newbie....and even if you are, who cares.....ya gotta start soemwhere dude.

Just get Jai or Nathan or any of the instructors to take you for a few laps to get a feel for the lines. :P

as far as cams licenses go, it looks like you will have to join up first then they send you cams forms and you send in yourself...to cams...

I think cams might issue you a temp. one quickly but you wouldn't want to leave it too close to the event which is the 25th march next one

You have to be a member of No Limits (or any other CAMS affiliated club) before applying for your CAMS license. Usually you can do all this on the night and Tracy will send off the paperwork. They will give you a paper slip which is your temporary license and it is valid for 30 days. You should then get your CAMS license book sometime after that.

You have to be a member of No Limits (or any other CAMS affiliated club) before applying for your CAMS license. Usually you can do all this on the night and Tracy will send off the paperwork. They will give you a paper slip which is your temporary license and it is valid for 30 days. You should then get your CAMS license book sometime after that.

yeah they aren't doing that anymore, because cams have dicked them around so many times..

now you have to join nolimits first ( thats your cams affiliated club ) then send the cams form ( which nolimits will give you ) in yourself......if you look on the nolimits site its just all change now.... ( in regards to CAMS )

still well worth the effort, you just can't leave it till on the night anymore....

  • 1 month later...

its next thursday again.... still need more people. www.nolimits.com

I'll be there in my my new toy , R33 gtr 760hp. :D 2.8L hks goodness.bought off sly33 on this forum..( still hasn't arrrived yet )

its great night, get into it..........

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...