Jump to content
SAU Community

Recommended Posts

1995 R33 GTR V-Spec Midnight Purple

For those of you that followed the build thread, here's the finished product. (clutch was able to be adjusted and now easy as to drive)

Totally regretful sale but im just not going to be in the country to enjoy it.

Fresh total mechanical rebuild from intercooler to exhaust tip, just run in.

HKS step2 2.8 stroker, full counter crank and rods kit, CP pistons.

Brand new head from Nissan, Jun 272 in and ex cams, 10.8mm(?) lift, special retainers and all the jazz needed to support the cams and high revs, heads extensively ported.

Big dollar hypertune plenum and single throttle body setup

Custom alloy breather tank etc

Jun oil pump, N1 water pump, cant recall the brand of balancer, but its a good one.

Trust sump extension.

Turbonetics GTK-850 turbo and big Turbonetics external gate

OS Giken 2 way front diff

OS Giken cross mission 5spd gearset with input shaft 800+hp rated, quick shift kit

OS Giken triple plate clutch 800+hp rated

Carbon fibre super lightweight tailshaft (not currently fitted)

ATTESSA system fully inspected with all fluids changed

V-Spec active rear diff

engine made 760HP on engine dyno at ~25psi with screamer pipe

Current street setup with wastegate plumbed back into HKS 4inch exhaust

Huge alloy radiator, disgustingly thick Trust intercooler.

Fuel system to cater for 1000hp, in boot setup as in pics,

1000cc HKS injectors,

HKS fuel rail,

splitfire coilpacks

Motec M800 ECU

Genuine 18inch Impul rims all round with new tires

V-Spec shocks with Lovells springs

V-Spec Brembo's all round

Midnight purple paint in excellent condition. Will try and get some pictures with better light to show off the purple.

Excellent condition original interior with almost no wear in the usual places (seat bolsters, steering wheel etc)

66850kms on the car, 1050kms on the engine including the run in

12 months SA Reg including custom silver on black godzilla plates

All mechanical parts brand new and all work done exclusively by James Sutton at Nisspeed Performance Engines.

Silly money spent and not used since run in. NO EXPENSE SPARED ON THIS BUILD.

Relocating overseas, asking price $45,000, however ALL GENUINE OFFERS CONSIDERED.

Test pilots forget it, will not be entertained. Genuine buyers only.

I WILL NOT BE CHECKING BACK HERE REGULARLY. Please direct all enquires to email:- [email protected]

DSC00039a.jpg

DSC00044a.jpg

DSC00053.jpg

DSC00054a.jpg

DSC00058.jpg

DSC00062.jpg

Edited by SLY33

^^yes I do have a stubby shifter but this big one is real easy to shift.

Balancer is ATI

Awesome power, car sounds like a jet taking off. Has an idle like no other street GTR ive heard, can really hear the cams. Will try and hook up a youtube link...

2 Way front diff means it doesnt change lanes on you from torque steer when you nail it, this thing tracks straight ahead, just hold on!

Now listed on carsales, more pics going up soon.

After bring it home Ive driven this car just TWO short times around my suburb! I fly back overseas tomorrow for good. Spent a BOMB building this car, this is how people get crazy bargains. Just try building it yourself, set a budget and you end up doubling it once your done. And dont forget the headaches that you didnt see coming!

This car is COMPLETE. Real sweet to drive.

Edited by SLY33

f**k!

for my sake, i hope its still for sale in 6 months time!

but i wont be suprised if its gone and youll we hoping its gone lol

goodluck!

Edited by Import S13
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...