Jump to content
SAU Community

Recommended Posts

have a whole bunch of stuff forsale, it is as follows, with pictures below

1. Nismo Twin plate clutch and Flywheel, im no clutch expert.. but would say suits rebuild and not sure what RB exactly it suits, someone may be able to tell from the picture, if not inspections are welcome - $450 neg.

2. Cusco Comp S R32 GTR rear coilovers - looks to be in good condition with no leaks, just a bit dirty - $450 neg.

3. Bilsten R33 gts-t rear shocks - also look to be in good condition - $350 neg.

4. R32 GTR standard shocks and springs - (Front only) - good condition - $150

5. GTR front mount intercooler - a few dings, but nothing that affects flow - $150

6. R32 GTR std. fuel rail and reg - $40

7. R32 std fuel rail, no regs - $30

8. S13 std. Air box - $50

9. Dump pipe of some description, i think its WRX - $40

10. KU36 brand new 235/45/17 - still has sticker, brand new $150

11. R33 Gts-t Series 2 Dash cluster with 87,000kms - $150

located in melbourne

if anything i have listed is incorrect, please inform me and i will edit it. thanks

post-17884-1266747952_thumb.jpg

post-17884-1266747973_thumb.jpg

post-17884-1266747998_thumb.jpg

post-17884-1266748018_thumb.jpg

post-17884-1266748032_thumb.jpg

post-17884-1266748051_thumb.jpg

post-17884-1266748069_thumb.jpg

post-17884-1266748084_thumb.jpg

post-17884-1266748111_thumb.jpg

post-17884-1266748124_thumb.jpg

post-17884-1266748380_thumb.jpg

Edited by Ruffels

haha stop being lazy ric, thats a good price ive got on those... exactly the same ones sydney kid uses in his suspension setups, just needs the extra grooves cut if you want height adjustment.

350 if you get the grooves cut (or at least organise to have it done) ... i'll even pay to replace those horrid choppies sitting on there haha

bilsteins SOLD

GTR cooler SOLD

Cluster SOLD

tyre SOLD

Airbox - SOLD

Cusco's - SOLD

Dump pipe - SOLD

______________________________________

STILL FOR SALE

Nismo Twin plate clutch and Flywheel - $370 (price drop)

R32 GTR standard shocks and springs - $100 (price drop)

R32 std fuel rail, no regs - $30

clutch is used, and most likely suits rebuild... its a push type clutch suits early rb26 and r23/33 gts-t

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...