Jump to content
SAU Community

Recommended Posts

i got defected in vic and my car is reg in nsw, so how does that rule work then?

Damn good question! Should have told them to shove it up their ass as VIC cops have no juristriction over NSW cars other than obvious things like fines for speeding or rbt's.

A car that is registered to drive in one state, may not meet the requirements of another state - but you can't be defected for hardly anything as how do they know all the rules of the other state? Obviously, things like bald tyres or tail-light out are universal - but i don't think they can pop your bonnet or anything like that. Interesting point.

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

I think the H pattern one is insane and I would never pay a fine for it. The rest I guess we can all understand so meh.

:zap:

I have blown my bov into two cops cars, totally accidentaly up here and had no problems, its more if your being a tool here they will lube you up and go some party dong on you.

lol stef

i got a sticker from those "Artistic" guys at pipeworks today, $5 lol i stuck it near my ashtray/boostgauge, wouldnt fit anywhere else lol

so yes gotta get spacer for numberplate from work, then have to get cat fixed and should be fine, oh and brighter break lights...how the **** do i do that?

ok cool i'll sus it out tomorrow

parents have done on holidays to nz for 2 weeks as of last friday so yeah can slowly do all this stuff hopefully i can take car in by friday the latest, just have to go to vicroads huh?

passed road worthy with no hassles, props to sam for directing me to darebin tyre and service centre frank is cool ;)

and thanks jack for the tow this morning as well (yesterday was my last day i was allowed to drive my car)

and thanks to greensborough vicroads, they are teh coolest

frank totally disregarded the h pattern said its useless hahaha and thankfully the canary fell off the 1st night and i stuck it on with sticky tape, i dont have any left over paper stuck on my windscreen

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...