Jump to content
SAU Community

Recommended Posts

I have no idea why or how but i THINK i have coolent coming into my cabin from the foot vent in the car and its all over the carpet and it only comes out when i corner?????

My car did over heat a lil the other day but now its all back 2 normal but i just wanna know why this shit is leaking into my car?!?!?!?!?

Plz help!

Link to comment
https://www.sau.com.au/forums/topic/30976-liquid-comin-from-front-foot-wells/
Share on other sites

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

Umm MadGT4. of course its coolant, how do you think your cabin heater works, engine coolant is pumped through the firewall and into a metal heater core. It corrodes like any other part of the coolant system.

Id seriously stop driving the car whilst its leaking, loss of coolant will cause your car to overheat and if you think running an engine without oil is catastrophic, wait till you run it without water! Best way to bin a motor.

Id doubt its just a hose leak, or else it would be leaking more constantly.

Heater cores are not easy to replace, they involve removing alot of the dashboard. If i were you id get the screwdrivers out and remove the core yourself then take it to a radiator shop for repair. Or else you'll be paying a mechanic at 50-80 dollars an hour to do a job that could take a whole day to do.

red17

Bugger!

Thanx for the tip looks like i might be doing that then

And its not inconsistant its like consistantly leaking so yeah and mainly on the passanger side for some unknow reason, theres only a very small amount coming into the drivers foot well...

Um now does anyone know how easy/hard it is to remove basically all the dash like Red17 said?

Although the liquid is probably coolant, it could be the aircon's refridgerant. When I had a leak on my AC system, I took it to my nissan dealer who regassed it and added some kind of green dye - the idea being it would be easier to detemine where the leak was coming from. The dye looked exactly like engine coolent...

if the leak only occurs sometimes, check to see if it only happens during/after using the AC...

i had this, started off small, the one nice winter morning the thing sh!t itself and i had steam billowing out the windows! bypassed the core and had to buy a new core for almost $400! just need to put it in now!

guys if ur heater is the problem u can still drive it as long as u turn the heater off . if u have climate control put the temp on the lowest seting 18 deg .

one way to check if its the heater when the car is at normal temp and when the ambient temp is say bellow 24 c put the heater on at the highest seting thats when the coolant should come in the cabin .

I guess its more pronounced, when the climate control is using a bit of heating to get a nice temp. Set at about 24c (18c gets too cold, even on 35deg days!) i guess that is when its been happening and it would be swapping between aircon/heating to maintain that.

Today - after removing my floormat, and seeing how much has been coming out - the loss from the radiator *does* match the leak, and its bigger than I inititally thought. Even just idling at standstill was enough to take a noticeable amount from the radiator.

Anyhow, i'm on the case... i can't drive around much with this happening for too long, as there is the risk of cooking the engine if it isn't topped up enough. Anybody who is having this problem *always* check the water level in the radiator and top up as necesary. For those that aren't aware: NEVER do this when the engine is already hot, as cold water into warm engine = cracked head

ok, well this arvo i've been pulling it all apart. Took some photos too..

First photo is the coolant that you can see on the carpet.. 2nd is the actual water as it drips down. While it looks like one exact spot, water is actually leaking from a number of places to under the carpet.

Further to wrxhoon, its not actually *that* hard to get to I didn't think once you have worked it out.. You can remove the whole glovebox assembly, letting you get easy access to behind where all the heater stuff is. No need to remove the whole dash.

Getting too hot so i've had to take a bit of a break, will keep updated on future progress.

ok, here is the glovebox after i'd taken it out..

To remove it, there are about 6x screws (circled red in the attachment). 2x of these are actually the catch to the glovebox, but you'll have to remove these also. Trickiest one is the one bottom right, which you'll have to do with the glovebox open, and using a long philips head to get in there.

After that you'll have to kind of pop the clips out (circled green) which attach to the upper part of the dashboard. I snapped one because its hard to do it without doing that :D but superglue will fix it.

Once you've done all that, you should be able to lift it all out as one piece, allowing you to get to all the heater stuff...

This should be what you can get to after you've got all the glovebox out. I assume this is the "heater core", although i'm still not quite sure what that means, i guess its like an element.

I guess i'll find out once i get it apart and/or out. Looks like you can take the bottom part out. Thats my next attempt :D

This should be what you can get to after you've got all the glovebox out. I assume this is the "heater core", although i'm still not quite sure what that means, i guess its like an element.  

I guess i'll find out once i get it apart and/or out. Looks like you can take the bottom part out. Thats my next attempt :rofl:

Yeah that looks like the airconditioning unit,,in behind that is the heater core,, it looks like a minature radiator with plastic surround with 2 plastic hose connections coming from it,,,,, i called Natrad in melborne and they got me one supplied for $250 brand new shipped down from canberra.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...