Jump to content
SAU Community

Locating A Plug For The Power Fc Map Sensor Port... Where?

GTRNUR

By GTRNUR,
in Engines & Forced Induction

 Share

Recommended Posts

GTRNUR Grand Master

GTRNUR

Posted
Posted (edited)

Hi all,

Im trying to locate a 3 pin female connector that plugs into the 3 pin port on the power fc ecu's to accomodate an external MAP sensor. Does anyone have an idea where I can source something that will fit?

Ive tried pulling apart a few computers and power supplies, but have had no luck yet. Jaycar and DSE dont stock anythign that comes close to fitting either.

Im beginning to think it will be easier to open up the ecu and solder on a diferent connector, or fit an external lead. Anyone have any suggestions before I do this?

Cheers,

Ian

Edited by GTRNUR
GTRNUR Grand Master

GTRNUR

Posted
  • Author
Posted

I dont want to use the boost controller kit for the FC. I just want to hook up a pressure sensor for data logging, so I need the plug that comes with the apexi map sensor.

The apexi map sensor doesnt have the range of operation that I need, so im using a different sensor. Sourcing the plug is the problem, and buying a boost controller kit to get a 30 cent component isnt an option.

GTRNUR Grand Master

GTRNUR

Posted
  • Author
Posted

I am after the 3 pin version of this plug. The pictures below are for the plug that is for PFC's that use the 5 pin boost controller harness. Its more of an general electronics grade connector than an automotive grade connector.

PFCBoostControlConnectorA.JPG

PFCBoostControlConnectorB.JPG

PFCBoostControlConnectorC.JPG

paulr33 Grand Master

paulr33

Posted
Posted

nengun.com has the loom as a seperate part (ie not in the whole kit)

and you can also buy the map sensor seperately

i did this on my r33 to get boost display on the hand controller without the boost control kit

49C-A002

Sensor harness 3P For Boost con 415-A001

AU $ 43.23

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Axles

      By GTSBoy · Posted

      There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • jdniss
      Forced Performance Hta Turbos

      By jdniss · Posted

      Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • thozza
      Intro/R33 owner

      By thozza · Posted

      Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Lithium
      Forced Performance Hta Turbos

      By Lithium · Posted

      Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • tidi0x
      R33 GTST Axles

      By tidi0x · Posted

      The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...