Jump to content
SAU Community

Recommended Posts

Hey forum I am having a problem starting my car and wanted to get some other advice on it. I have an rb25det with the series two engine so no ignitor module. Mods that might affect startup are are pfc, z32 afm set in pfc, nismo 555 also set in pfc, q45 throttle body and brand new super spark coil packs. Here is the problem as I try to roll the car over it cranks but just will not start. I have power to the injectors and fuel pressure. Do not know if fuel is being delivered as I didn't remove any hoses but can smell the vapors as I try to crank. I checked the power to coil packs but got nothing. I wanted to know if at ignition on should there be a constant hot to the coil pack loom? Cause I turned the ignition to on and checked every wire coming from ecu loom to coil pack and none had voltage. I also did the check in the manual for continuity between certain ignition wiring and got nothing. So I was just wondering are there any other checks I can do to the ignition system to prove this is what is wrong?

Link to comment
https://www.sau.com.au/forums/topic/310241-car-will-not-start/
Share on other sites

what did you last change

when did it last start ok

I changed everything. Last started ok before rebuild. Did a complete rebuild. Put on new intake, new exhaust, new injectors, new computer, different harness, different turbo and throttle body. Everything else is ok by my test throttle body .4 volts at ignition, injectors have a constant hot and pulse when cranking the car, have fuel pressure all lines are installed correctly and can smell vapours when cranking didnt remove any fuel lines, but I think those fuel checks were enough. Only problem is at ignition on can't find a hot on coilpack plug from ecu. Thats why I think I have narrowed it down to ignition, and was wondering if when ignition on should you have a constant hot to one of the wires from ecu loom to coil pack loom. During sensor check on pfc got throttle voltage and 3.54 volts on wtb something.

I changed everything. Last started ok before rebuild. Did a complete rebuild. Put on new intake, new exhaust, new injectors, new computer, different harness, different turbo and throttle body. Everything else is ok by my test throttle body .4 volts at ignition, injectors have a constant hot and pulse when cranking the car, have fuel pressure all lines are installed correctly and can smell vapours when cranking didnt remove any fuel lines, but I think those fuel checks were enough. Only problem is at ignition on can't find a hot on coilpack plug from ecu. Thats why I think I have narrowed it down to ignition, and was wondering if when ignition on should you have a constant hot to one of the wires from ecu loom to coil pack loom. During sensor check on pfc got throttle voltage and 3.54 volts on wtb something.

Da Boss, please put your stock or any other injectors in and change those yellow foolishness. I told you they are no good. Trust me on that. Once you do that you will be fine.

Sparta!

Da Boss, please put your stock or any other injectors in and change those yellow foolishness. I told you they are no good. Trust me on that. Once you do that you will be fine.

Sparta!

Lol, I hear ya. The yellow foolishness good though they got stuck from just sitting up there, had emm flow tested an freed they all good now. So Any other ideas, Mr Sky, I tired a catching ride now and these sr20 guys running the streets now, "So I heard.", and skyline fellows demolishing the cars. I have it narrowed down to ignition cause when cranking I get no power aor signal at the plug that comes from the ecu. I think that part a the harness is fried.

Lol, I hear ya. The yellow foolishness good though they got stuck from just sitting up there, had emm flow tested an freed they all good now. So Any other ideas, Mr Sky, I tired a catching ride now and these sr20 guys running the streets now, "So I heard.", and skyline fellows demolishing the cars. I have it narrowed down to ignition cause when cranking I get no power aor signal at the plug that comes from the ecu. I think that part a the harness is fried.

i was having the same simptoms as what you are explaining, try different injectors first and see how it goes.

Hey there forum, need to ask another quick question found out that the wire harness I am using is from an automatic skyline and mines is a manual. Was told if I am using a manual transmission with this automatic harness I will have no ignition. Do you think that is the reason I am getting no ignition? If so what do I have to rewire in order to get ignition.

yeah because different injectors will stop power going to the ignition coils :)

there is 3 wires into the ignition coil.

one will be thicker. this should be the ignition power.

you should be able to check the other 2 colour and see 6 of them that match at the ecu(loom)

these should have pulses when cranking, but you can only check with a led test light.

if there is no power to any of these wires when ignition on then there is your problem. get a multi meter and see if the thick ones all have continuity to each other. if they do and theres no power, try tapping into one of the thick wires and put a temporary 12v feed straight from the battery, then try cranking it again. see if it starts

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...