Jump to content
SAU Community

Wrecked R32 Skyline + Rb20det Parts

Nissan r32
 Share

Recommended Posts

Nissan r32 Collaborator

Nissan r32

Posted
Posted

All parts are out of a 1993 model R32 Skyline 2 door. Parts include:

Drivers seat $50

Rear Seat $60

Rear centre seat belt $20

Window wiper motor $40

Air con pipe (firewall to compresser) $20

GTST Bonnet (Silver) $100

Drivers door (Black) with glass and power window motor $100

Boot Lid (Black) Slight repairable damage $30

Stock dump pipe (Turbo to cat) $30

Stock Cat $20

LSD Diff centre $180

Manual Tail shaft $100

Brake Booster $40

Rear Brake calipers + discs $60 the pair

® Rear quarter trim (Bottom half) $20

Scuff plates + Clips $30pair

Pioneer detach face stereo 200w $20

Base 10" sub in box 500w $20

Indicater stalk + horn wire (Complete unit) $100

Boss kit $30

Front strut brace $30

Interior light $10

Rear view mirror $10

(L) Electric mirror (Black) $50

Door check straps both $20

All door lock rods + Clips (both doors) $20

Electric sunroof switch + Interior light $50

Centre dash tunnel surround $10

Passenger glove box door $20

Climate Control Unit $100

Nismo gear knob + handbrake lever both new in box (Never used) $50

Drivers side plastic guard liner $20

Space saver spare wheel $40

Timber plate to cover spare wheel $20

Stereo brackets + Compartment $20

Fuel Flap (Black) $40

Fuel Cap (Nissan) $10

Number plate lights + wiring and fuses $20

Lots of RB20det Engine parts: Motor only done 82000km:

Crossover Pipe with BOV mount + gasket $50

Top + Bottom Radiator hoses, near new $30

Clutch Fan $60

Coil packs x6 $80

Coil pack plates + bolts (to hold coil packs in place) $40

Igniter $40

Pulley belts x 2 $20

Throttle body (Complete) $50

Inlet manifold $80

Stock turbo + Wastegate actuator $350

Stock turbo oil + Coolant lines $30

Crank Angle Sensor + Bolts $50

Stock front mount under bonnet piping (all) $60

Alternator (Gen Nissan) $60

Power Steering pump with bracket $100

Power steering reservoir $20

Century Battery, near new $50

Air flow to BOV Steel pipe $20

Engine mounts $50 each

Harmonic Balancer $80

Fly wheel $60

Starter motor $80

RB20det Engine Block and head Complete $500 Good for someone who needs a bare block and head

and can swap all there stuff over onto. E.G: If your RB20 is blown, heres a good motor for you,

just need to swap all your stuff over.

RB20det 5 speed Gearbox (No crunches, or noises) Very clean, smooth and quiet box $500

Im located in Ashfield (Sydney)

Postage can be arranged at buyers expense

PM or contact me on 0415126075

Cheers Sam

Link to comment
https://www.sau.com.au/forums/topic/310465-wrecked-r32-skyline-rb20det-parts/
Share on other sites
Nissan r32 Collaborator

Nissan r32

Posted
  • Author
Posted
Any mint sunroof parts kickin around? I need it all except glass, switch and motor.

Thanks.

Mike.

Hi Mike

Sorry mate all I have for R32 Sunroofs is the switch unit with the interiour light.

Let me know if you want it.

Cheers Sam

Nissan r32 Collaborator

Nissan r32

Posted
  • Author
Posted
have you got the tyre plackard? if so how much

Hi mate

Sorry I don't have the tyre plackard. I think you can get them on ebay bro

Cheers Sam

Nissan r32 Collaborator

Nissan r32

Posted
  • Author
Posted
Hey bud i'm looking to buy ecu + wiring loom, airflow meter and maybe the coil packs and igniter.

How much $$ and will you post to S.A?

Hi mate PM Sent

  • 1 month later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...