Jump to content
SAU Community

Recommended Posts

as above to get into diagnosis mode turn ignition to on (i.e power on the dash but car doesn't have to be on) and press the driver side door switch 5 times within 7 seconds. If you have done this right you will see the airbag light blink slow and fast the way it's blinking is actually telling you what is wrong but as there likely isn't anything since you plugged everything up just turn the ignition off and back on again shouldn't blink anymore.

If it's still blinking try again and if still no luck tell me and i'll send you something that tells you what needs to be sorted

Hi ,

I am encountering the same problem when I disconnected the steering wheel airbag to realign steering wheel and forgot to plug connector back into place before turning ignition on. Once the airbag light starts flashing,it would not stop even after reconnecting the air bag.

Its driving me insane!!!!! Please help, I have tried turning the ignition on and pressing the drivers door light, but the light is still FLASHING!!!!

Please help

Matt

I tried the Door switch trick and did NOT work for me. The driver door switch is the one on the B pillar, close to where the door latch is located??

It's the little light switch that turns the interior light off when the door closes

try doing it but try having it pressed in before you start or some other method. I had to change my sequence a bit because it didn't work for me either, but by changing it to suit my var it worked fine

  • 4 months later...

Can someone post the codes for what the blinking stuff means?

After entering diagnostic mode (pressing 5 times (hold the button down for a while don't just press it madly) within the first 7 seconds.

... its off long on long, on short off short. repeat.

f**king computers...

As someone who designs systems for a living i'm more than qualified to say.... f**king computers...

Not to be outdone... I went back and repeated the whole process... (got in car... ignition to ON 5 firm presses)... no light. Turned ignition OFF. Started car. Light stayed OFF.

Win.

I didn't know bill gates was Japanese and worked for Nissan??!? ... f**king stupid computers... lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
×
×
  • Create New...