Jump to content
SAU Community

Recommended Posts

Hey guys,

Just wanted to find out for sure if the stock GTT ECU has an ISO14230 connector? I am looking to buy a Greddy Informeter Touch, which is an OBD2 monitor that plugs straight in to the ISO14230 connector. It can also connect to Nissan CONSULT. I just want to make sure that it is compatible with my car before i buy it.

Cheers,

Martin

Link to comment
https://www.sau.com.au/forums/topic/312173-question-about-stock-r34-gtt-ecu/
Share on other sites

I just went and had a look at my car, and there is a little panel that pops out down near my feet, near the bonnet release lever. There is a wiring harness that comes out from that, would that be my ISO14230?

it should be consult

Thanks for that mate.

I will have to get confirmation from Greddy about whether it can measure boost, oil and water temperature with the non-OBD connector. I may end up going with ARK MFD as that just splices straight into the ECU's wires so it is compatible with any car... Will wait to hear back from Greddy first though.

Thanks for your help guys

thats OBD2 port so i would say yes

just in case anyone reads this and thinks its correct, its not. R34 does NOT have an OBD2 port, only a consult port. V35 and up have OBD2 port.

so yes it has the consult port. OBD1 isnt really a standard, people just use OBD/OBD1 to often mean 'something which isnt OBD2', so its not good to use OBD/OBD1 in terms of identifying a diagnostics port at all.

the ECU doesnt read boost and oil, so unless the touch has external wiring for that, you wont get that.

make sure you consider the ECUTalk V2 display before spending 3 times as much on a toy.

normally for monitoring people will get a consult device + gauges for the un-monitorable via consult (oil temp and/or pressure, boost, and sometimes wideband o2 and EGT).

just in case anyone reads this and thinks its correct, its not. R34 does NOT have an OBD2 port, only a consult port. V35 and up have OBD2 port.

so yes it has the consult port. OBD1 isnt really a standard, people just use OBD/OBD1 to often mean 'something which isnt OBD2', so its not good to use OBD/OBD1 in terms of identifying a diagnostics port at all.

the ECU doesnt read boost and oil, so unless the touch has external wiring for that, you wont get that.

make sure you consider the ECUTalk V2 display before spending 3 times as much on a toy.

normally for monitoring people will get a consult device + gauges for the un-monitorable via consult (oil temp and/or pressure, boost, and sometimes wideband o2 and EGT).

Thanks for clarifying mate.

Both the Greddy Infometer and the ARK MFD have adaptors to plug in additional sensors for boost, oil temperature/pressure, water temperature, and wideband o2 and EGT. So that is no problem.

At this stage i think i will go for the ARK MFD as it does not use the diagnostic port, however if the Greddy Touch can still display the optional sensors with non-OBD then i would rather go for that as it has more functions.

I have looked at the ECUTalk V2 Display, but i think for almost a similar price as the ARK MFD, with less functions and, lets be honest, horrible appearance, the ARK MFD or Greddy Touch would be the better option

isnt the ARK MFD more than double the ecutalk?

guess it depends on what purpose you need it for, and whether you need it just for its functionality or if it has to look the part also, which the ecutalk display is pretty plain.

i would have thought that the 3 sensors not available via consult, you'd want boost and oil pressure as standalone gauges? so then you're really only getting oil temp more than whats available via consult.

ARK MFD is about $400 and can read boost straight off the bat, doesn't need additional sensors. It is mostly for functionality, but looks does come in to it, i don't want an 80's looking gadget. That and the fact that i find the ARK MFD a hell of a lot easier to read, rather than trying to make out what the ECUTalk is saying.

I will need to get the additional sensors for oil temp/pressure, and water temperature. But i find the price of the ARK MFD + sensors better than the price of all the Defi gauges i would need to monitor all the things the MFD can monitor.

where have u found it at that price? ark website has the unit at $459 + $79 temp sensor, $179 pressure = $717USD. im sure you can get it cheaper elsewhere etc, but thats quite a lot of dollars.

which readings/screen would you monitor 24/7? (i see theres a 4 gauge or 8 gauge mode, presumably one of those?).

and comparing to cost of defi gauges is going to make anything look cheaper :blush:

i guess one of the benefits of the ARK is that it doesnt take the consult port, so if you wanted to add something off that later you can. anyway looks like you know all your options, good luck.

  • 3 months later...
ARK MFD is about $400 and can read boost straight off the bat, doesn't need additional sensors. It is mostly for functionality, but looks does come in to it, i don't want an 80's looking gadget. That and the fact that i find the ARK MFD a hell of a lot easier to read, rather than trying to make out what the ECUTalk is saying.

I will need to get the additional sensors for oil temp/pressure, and water temperature. But i find the price of the ARK MFD + sensors better than the price of all the Defi gauges i would need to monitor all the things the MFD can monitor.

I am also looking at getting the GREDDY INTELLIGENT INFOMETER TOUCH, but did not want to open a new post.

Did you end up getting this ?

I have got a r34 GTT 98 and was hoping to get the Greddy Infometer.

From what I have read it should be okay as long as you get the additional harness for Nissan CONSULT ?

I have looked through the forum and this seems like the latest talk about this.

Thanks

P

Nah didn't end up getting it mate, went with the ARK MFD instead as it wires straight into the ECU so I didn't have to purchase an extra cable. The ARK also comes with a boost sensor, so didn't have to purchase another sensor. In the end worked out about $400-$500 cheaper, and it's really easy to use :whistling:

  • 6 months later...

Nah didn't end up getting it mate, went with the ARK MFD instead as it wires straight into the ECU so I didn't have to purchase an extra cable. The ARK also comes with a boost sensor, so didn't have to purchase another sensor. In the end worked out about $400-$500 cheaper, and it's really easy to use :whistling:

You need the Infometer touch with a non-OBD (Nissan) connector.

Seems about the same price as the ARK MFD but you don't have to hack into the loom and has no buttons - just touch goodness.

Much better than buying Defi gauges which are even more wallet raping.

Given the cost you're looking at outlaying, and you still have to find somewhere to mount it, and given you have an R34 - have you considered just retrofitting an R34 GTR MFD?

There are plenty of tutorials/guidelines on how to fit - it will display boost/ignition duty cycle/water temperature/oil temperature/throttle position (and intake/exhaust temp if you fit extra sensors).

You'd probably be looking at $900-1000 for the unit + a few hours to wire it all up. Definitely an option in my opinion.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...