Jump to content
SAU Community

Recommended Posts

do you have the boost control kit?

when the PFC is data init'd to defaults the boost kit is turned on by default

this means, if yours was "reset" and you aren't using the boost kit the engine check light would remain on until you disable the boost control kit

the PFC has no limp mode or back out mode other than what the stock ECU has

and this is your typical if AFM is dead, cap rev limit at 2500rpm etc - really basic rev cuts and idle protection

it wont know if your fuel pump is being gay or leaking fuel etc

im not sure, it has a setting for boost control i think, but i have a HKS EVC as well, so not sure there.

BTW here are the mods:

RB26

Trust T78-33D

PowerFC w/Commander

HKS EVC5

Trust Manifold

Trust External Gate

Tomei Type-R Poncam

SARD Injectors

Adjustable type fuel regulator

HKS Pod Filters

Z32 twin AFM's

Trust Intercooler

Trust Oil Cooler

3-Layer Copper Radiator

Low temperature Thermostat

Turbo Back Exhaust

My god son get it to a tuner it's obvious that the tune is on default maps - and by the sounds of it if there is no fuel leak than you must be hosing those bores with fuel. If it's got an issue withtge maps not storing than ashas been said check the keep alive batteryinput into the ecu - if it's good get a new PFC.

gave it a basic settings change last night, car is now running fine (albeit with less power and tonnes of lag)

for anyone interested, these were the settings i was given:

Seq.turbo cont ... default = on ..change to OFF

Inj/AirF Warn. ...default =on...change to OFF

Knock Warning ... Default on .....Leave ON

O2 F/B control (O2 sensors) ..Default =on...Change Both to OFF

Idle-IG Cntrl....(O2 Regulation) Default =on.......Change to OFF

then turn my injectors (beleived to be 700cc) down to 75% from the factory 100%.

for some reason the first setting (seq turbo) wasnt there, instead the boost kit option was there. i did everything by the notes, and left the boost kit on just to see, got a huge fuel cut, and sent the knock to 30. turned the boost kit off, and it seems to have disappeared.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...