Jump to content
SAU Community

Recommended Posts

Hey all,

Have a few turbos and other bits and pieces to get rid of :

Two hiflowed gtr turbos, steel wheel Ball bearing standard housing sizes. Turbo's have only seen about 15 thousand k's as my motor threw a bearing.

Excellent condition and you can hear them spinning for ages after the car is off... really going to miss these.

want $1000 for them.

I have two GTST turbo's one with the actuator on it the other without it. 300 for the one with the actuator on it and 250 for the other one.

ZERO shft play in both, excellent condidtion.!

Have a mines ECU for an R32GTR : $300

2 R33 RB25det ECU's, : 100 each

Carpet from R32GTR : Make on offer

G-Sensor from GTR : make me an offer

R33 GTST/GTR Radiator : $100

GReddy boost guage with all the bits and peices, Black face : $150

Center guages from R32 GTR : $50

R32GTR glovebox : offer

More to come, will update when I check what else I have.

Send me a message I will be checking this regularly :(

Cheers all!

On the GTST turb's lets say about $15 postage... I can't forsee it being too much more than that. and if it's les I can put the difference in the post packet :D)

Cheers,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...