Jump to content
SAU Community

Recommended Posts

hey guys !

I've noticed a problem with my 33 gtst lately, when I floor it in first and hit second I seem to get heeps of lag in second where the boost gauge sits on about 3 to 4 psi, then after a second or so hits up to the 8-9psi setting. I'm using a bleed valve but have never noticed this problem before.

Any ideas people ?, one mate did suggest the wastegate could be sticking a little.

Thanks in advance..

Lenno

Link to comment
https://www.sau.com.au/forums/topic/31304-boost-drop-between-gears/
Share on other sites

Did you bypass the standard solenoid when installing the bleed? It sounds like you haven't, because the standard solenoid has a 2 stage boost process, where before 5000rpm (or there abouts) it will cap the boost to around 4-5psi, then after that hit 7 psi (or 8-9psi with exhaust)

Try swapping your bleed with a mates if you can and see if the problem persists. If that does not fix it then I would say that you waste gate might be catching???

other than that I am stumped, cant think of why it would only happen in second. Do you have an auto or manual?

Heres one from left field.

Have you considered that the rears may be spinning so the drop in revs when you shift to second is dropping the engine below the boost threshold.

I have this problem in spades if not careful as i'm running a high flow turbo on an rb20 that doesn't start makin decent boost until about 4000. With a stock turbo this is unlikely

I've also had a problem in the past of a gated bleed valve not releasing pressure in the line to the actuator and holding open the wastegate, though this was preventing any boost coming on until 6000 or so.

Thanks for all the ideas guys, the bleed valve i'm using is 2 mths old and is the turbosmart brand, the car is a manual.

i'll try swaping the valve and see what happens.

BHDave you could be on to something... the wheels usually are spinning just before i hit second, but then still spin into second even though the boost lags for a second..i'll have to investigate further.

cheers

Lenno

You'll find that boost will drop off once the wheels start spinning because you can't maintain load on the engine, so your turbo will be spinning slower to start with and then slows a bit more on gear change.

Out of interest is the bleed a turbosmart single stage with incabin switch? and does the problem only happen in low boost mode? Mine was put together wrong in the factory and i had to fix the bastard.

bleed vave is under bonnet type. whats got me stuffed is that it will still spin into second pretty hard but still feel laggy and as i said boost slowly swings to about 4 - 5psi then rockets to 8-9, all at about 4000 revs, as revs dont really rise untill boost does..

I'll have a chat with the mechanic and get him to drive it, see what he thinks.

cheers

lenno

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...