Jump to content
SAU Community

Exhaust Manifold Studs

mr_mate

By mr_mate,
in General Maintenance

 Share

Recommended Posts

mr_mate Newbie

mr_mate

Posted
Posted

i pulled my manifold off my 20det the other day and had a total of 6 snapped studs (f**king bulls**t) so i went about drilling them out and managed to get 5 of the bastards out but the one closest to the firewall just wont budge. iv snapped an ezi out in there already and made a mess of the hole when drilling it again and i dont want to snap another ezi out in there. i dont have the funds (uni student) to pay someone else to do it for me.

so the big question is: is it an alright idea to leave it alone and just have 11 new studs holding it on with a bit of manifold cement, or will i loose heaps of grunt from escaping fumes?

any help would be appreciated.

im also from NZ (the NZ forums suck balls) so no point recommending me to anyone in AUS. cheers

Link to comment
https://www.sau.com.au/forums/topic/313441-exhaust-manifold-studs/
Share on other sites
aerofocker Enthusiast

aerofocker

Posted
Posted (edited)

its best practice to get it out of there,seen as you have broken an easy out in the stud the option of drilling it out is limmited to useing a pencil grinder with a high speed rotary burr,if you have one of these you will be luckey lol the easyout should be too hard for a regular drill bit, plan b as stated above,and your best option in my opinion is to place a nut over the hole and weld through the hole in the nut on to the snapped stud,just make sure you chip the slack off periodically if your doing a stick weld easy outs are genraly a fail when it comes to these things for starters by there very nature they are a smaller diameter than the bolt to be extracted so inherintly weak

Edited by aerofocker
mad082 Grand Master

mad082

Posted
Posted

before trying anything again, go to your local car parts place. they should sell a product that comes in a can which you spray on the stud to freeze it. this makes the metal shrink and will make it easier to come out. in this case, spray it into the hole you have drilled for the easy out. be generous so it cools down as much as possilble. then stray away try the easy out.

grigor Rising Star

grigor

Posted
Posted

Here's a few suggestions.

First throw your Ezi-outs in the bin. They cause more grief than they're worth. In future buy a decent stud removing toolkit or pay someone.

Next you have to be dead sure that your broken Ezi-out was drilled true to the stud, not half in the stud and half through the head.

Now MIG a suitable sized plain washer over the broken stud. You'll be able to get a few good hits using a MIG.

Then MIG a nut to that washer.

Now you're ready to unscrew.

The heat from the welding will loosen the most stubborn stud, but if the washer/nut snaps off, just do it all again.

Admittedly that stud will be an absolute bastard to get at, but the manifold gasket will blow without all the studs installed.

OMGGTR Mentor

OMGGTR

Posted
Posted

yeh i got 2 snapped studs on number 6 cyl fkn depressing coz its to much work to do to my daily ... i wont be able to get to work so i gota leave it as is..... :( if ne1 can do it in less than 1 day ill happily pay u...

  • 8 months later...
jrh001 Proficient

jrh001

Posted
Posted

Here's a few suggestions.

First throw your Ezi-outs in the bin. They cause more grief than they're worth. In future buy a decent stud removing toolkit or pay someone.

Can anyone recommend a decent stud removing toolkit? I've tried Ezi-outs (actually an equivalent sold at Bunnings). 

An exhaust manifold stud has broken off below the surface. I can drill it easily but the remover just won't bite. (Engine is 25+ years old.)

JohnH

jrh001 Proficient

jrh001

Posted
Posted

and just fyi no having 11 studs won't work properly

you will get a leak where the missing stud is

Thanks, 

The engine was out of a running car - my fault when I bought it because I didn't notice the broken stud. The L24E only has two studs, one at each end of the engine, the rest is held in by bolts (all came out no drama).

Hoping that someone knows of a good remover kit. 

JH

jiffo Mentor

jiffo

Posted
Posted

Can anyone recommend a decent stud removing toolkit? I've tried Ezi-outs (actually an equivalent sold at Bunnings).

An exhaust manifold stud has broken off below the surface. I can drill it easily but the remover just won't bite. (Engine is 25+ years old.)

This company has the style of extractor you need, but it's always best to buy a name brand not Chinese stuff.

P&N, etc, names that have a reputation in the tool world.

http://www.tetools.com/catalogue.html

post-73571-0-40640600-1292382790_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      Welcome back brother 
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...