Jump to content
SAU Community

Wrecking R33

ang180
 Share

Recommended Posts

XFA993 Contributor

XFA993

Posted
Posted (edited)
95 series 1 1/2 R33 complete interior parts no front or rear seats already sold.

R33 rear cradle no diff and breaks

R33 powersteering rack & hubs

R33 Bonnet

R33 series 2 Boot with Wing, rear bar & rear lights

R33 series 1 headlights excellent condition

S15 front 5 stud hubs with breaks off non turbo s15

R33 rear 5 stud hubs no breaks

Series 2 drivers seat no rips or tears

ALL MUST GO PM OR CALL FOR what u need and for PRICE OR MAKE OFFER

0433329781

mate after a parcel shelf with childanchors have u got some? wil post to mel?

for r33 gtst s2

Edited by XFA993
  • 2 weeks later...
  • 3 weeks later...
  • 3 weeks later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      Bummer...yeah i "need" something to "ease" up the work and for my driving it would be enough.    Iam counting the tune "without" turbo. I do not mean "cheap" like something from Temu around 200 USD, "Cheap" is something around 1000 USD? 
    • GTSBoy
      Neil's R33 Gts-t Build

      By GTSBoy · Posted

      Starter motors used to use the weight of metal (magnets) to provide torque. Now they use (more) current instead. This. It's completely normal.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      So thing that had me stumped, but I think is OK....is that when it was up in the air, in neutral I had it running to bleed to coolant while I put the wheels back on. I noticed the rears were turning (slowly) which I'd never seen before 20250928_163512.mp4     Because there had been an issue with clutch slip due to pedal adjustment on the dyno, I assumed there was still and issue so spent some quality time upside down under the dash adjusting the pedal....but no matter what I did the wheels still turned in neutral. Even disconnected the master cylinder to pedal rod and same. In despair, I even removed the clutch slave so there was no chance of any preload causing it.....still happened. So either: 1. Something is not right in the bellhousing, or 2. Its a thing sometimes with cold, thick gearbox oil Internet says it might be 2, I hope so!
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, few more things sorted and it is ready for a shakedown on 10-Oct, with one weird thing. Changed the run in oil and filter for the good stuff. 8l came out, about 8.5 went in with filter so that looks all good. Changed the starter (again), this time for a brand new one, works good. Interesting that the Taaaarks one is shorter than factory but spins harder, I guess electronics have moved on a little in the last 30 years. Will be nice to have a bit of extra space under there. Put the timing cover back on, and noted where the cam gears were set as a record.  Will need to double check the timing but it is pretty close. Also put the coil pack cover and intake snorkel back on. Exhaust Inlet Changed the water out for coolant, bled up nicely. Removed the rear brake pads (well worn factory sumitomo ones!), gave the hardware a good clean and reassembled. I've put bendix XP on the back again because the price is excellent at $150 a set and they worked well on the V37. Front pads have plenty so no issue there
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

×
×
  • Create New...