Jump to content
SAU Community

Bypassing heater unit - HOWTO

predator

By predator,
in General Maintenance

 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

Seems like a lot of people are having the problem mentioned in this thread:

http://www.skylinesaustralia.com/forums/sh...ead.php?t=30976

Basically the cause is most likely a stuffed heater core, which involves pulling your entire dash apart, and its maybe 6-8 hours of work.

So for those that don't just want to do that just yet (but its recommended).. you can actually bypass the heater core altogether. Means you get no heat, and no proper climate control, BUT it also means you don't get leaking coolant, which can mean overheating and then the end of your engine!

For those interested: the heater core just works via coolant (which is heated from the engine) passing through a small radiator, which is in turn stores heat, and warms the car. The coolant then passes back through the firewall, and into the rest of the cooling system.

So, here we go:

1. Leave your car overnight, or at least a good few hours to let everything cool down, and water to settle back into the system.

2. First of all, remove the two hoses that go into the firewall (as shown). One is like the "in" and one the "out" coolant flow.

They are held on via clip type things. Undo the screws using a philips head or even an adjustable wrench. They can be a bitch to get to if not facing an easy direction, so slide them around if you can. A bit of coolant should come out, but when i did it, there wasn't much.

3. Use a piece of hose that will fit in between the two hoses to bridge the two. Luckily i had one that gave a tight fit @ 21mm outer diameter. Hopefully the small diameter hose doesn't cause a noticeable restriction in the cooling system(??). Probably a plastic pipe of correct size would be the most secure way to do it (didn't have one on hand).

4. Tighten up the clamps as tight as possible. Make sure its all secure, and try and angle things so the rubber hose is not too close to the engine.

5. Start her up and give it a test, check for leaks, and any sudden rise in temperature during a test-drive.

I did a short test run, and everything seemed to be normal and running ok.. but keep a razor eye on that temperature guage, and any leak from that area.

I hope this all ok, wrxhoon or the like might be able to have a quick check to see if i've done something no-no. I take no responsibilty for any damage caused by anything in this thread!

Link to comment
https://www.sau.com.au/forums/topic/31403-bypassing-heater-unit-howto/
Share on other sites
predator Grand Master

predator

Posted
  • Author
Posted

No need to plug anything.. The heater can just sit their disconnected without any problems. The heater core is just a small radiator really, where water flows in, and then straight out, heating it in the process.

Its possible you can just plug both ends of the hoses at the engine side, but i think keeping the original "flow" in and out of the engine would be best.

  • 7 months later...
JAPCAB Proficient

JAPCAB

Posted
Posted

Have a look around the firewall they must be there somewhere....i'd imagine they would put the heater in the same spot?!? Try unplugging some hoses and if you pull off the hose and see the yellow heater core plugs then you know u r on the right track. Perhaps have a look under the car - maybe they have mounted them lower if they aren't on the top

Anyone done this on a GTR? Where are the 2 hoses?
ferni Grand Master

ferni

Posted
Posted

yeah was the same place, just more crowded around the area, bypassed it for now, need to source a new heater core, i've been told copper is best, will last forever (well alot longer than a normal one)... then gotta get my dash out to replace it.... not really looking forward to it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...