Jump to content
SAU Community

Recommended Posts

Originally posted by GOT BOOST

looked the goods but very thin from a volvo car

but still better than top mount..

goota get one for the line now. ouch.

had my car measured up for some graphics today  

have on tomorrow.same as G SIGNAL style.

should look the goods...

ooh? oooh, graphics ?

Who's doin those ?

and where did you buy your R32 from ?

and you coming to the cruise tonight ?

GOT BOOST, that sounds pretty good for the mods you have. Ive got a grey R32 GTSt with 3inch from the cast dump to the tip, high flow 3 inch cat. Ive got a HKS EVC boost controller (currently not installed) and a Blitz Access computer which likes to dump fuel down the zorst resulting in satisfying faint *Booms* out the back end when you gas it up and back off.

Im guessing when i get the boost controller back in and up the boost a little the Blitz will come into action a bit more.

So, if you got 14 flat out of yours id be stoked just to get a mid 14 outta mine. After driving my brothers fairly well modded 180 on the weekend I was almost depressed hopping back into the 32 this morning! Just doesnt seem to get up and go the same

Anyhow if you see another 32 around rocko, its probably me :)

Red17

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...