Jump to content
SAU Community

Recommended Posts

Hi everyone, my r32 has an rb25det conversion done by previous owner. I have owened it for about two weeks now. I have done the usual services, oil change, auto trans flush and new spark plugs. Now the thing I am noticing is when under hard acceleration it wont boost past 6.5lb or seven if I'm luckily, its okay reving through the low to Med range but as soon as the revs get high it feels like its spitting or missing, when I take my foot off the the gas a little it kicks back in, slightly. I have checked all vacume lines I could see, which are all silicon hoses with no ties? The coil packs are stock as far as I can see but I would like to find out if it could be more basic before I fork out the cash for new coil packs. Any help would be great or directions to similar threads.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/
Share on other sites

Might help to tell us how much boost you SHOULD be running mate lol. 6-7psi is normal for 25s if my memory serves me correct...

Have a look for an exhaust leak, and/or boost leak.

Boost leak can indeed cause your missing/spitting, and an exhaust leak can cause a lack of boost/laggy feel

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5162762
Share on other sites

Lol sorry I'm running a gizzmo EBC. Set to 9.7lb, I noticed that the silicone pipe that connects the intercooler pipe to the factory inTake pipe on top of the motor has a tiny gap on either side of the tube, I'm not sure if this is due to them being over tightened or the clamps are not closing strait. How much gap would it take to loose that much boost? As far as the exhaust goes it factory dump pipe to 3" cat back. My mechanic put it up on the hoist and did not notice any exhaust problems, it looks pretty new actually.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5162792
Share on other sites

Yeah even the tiniest of leaks can cause a mass fire in RB engines, because they are MAF sensored...

Do you have a pic of said silicone coupler?

How old are your spark plugs?

They could be fouled and not firing properly, the boost is blowing out the poor spark if so, this would prevent your engine from making more boost.

Go through the length of your exhaust and check for studs that are loose, specifically the head-manifold and manifold-turbo ones.

Other than that, have a look at your spark plugs, replace that silicone coupler if it looks like its leaking, and double check all the vacuum hoses and electronics are working for the EBC. Maybe even try to disconnect the wastegate actuator and take it for a spin. Watch your boost gauge very closely and see if you can boost above 7psi. Not the safest method, but it will rule out if your EBC is the problem...

Good luck bro!

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5162824
Share on other sites

Oh and do just diconnect the actuator from the solenoid or do I need to block it up?

I would leave the actuator alone you can just turn your boost controller off and that should run wastegate pressure, would be a lot safer.

Still sounds like it could be coils, what gap is your plugs? 0.8mm is the standard most people run with standard coils.

Other than thats if its pulling smooth but boost is tapering off would just likely be able to fix that by playing with the settings on the boost controller.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5162861
Share on other sites

Ok, I have bypassed the EBC and noiticed it still holding boost but still maxing out at 5 sometimes 6lb. It doesn't "seem" to be plaining out or spitting now but there was a fine line between it spitting and not spitting.

what could be going wrong with the ebc? Could it have dual high and low settings

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5163195
Share on other sites

Okay, I have installed all new clamps on piping and ties on vac lines. Now its hitting boost a lot better but its still spitting, it only seems to do it when putting my foot right down, but not when i accelerate just a little, so I'm assuming that's why its still not hitting its full boost.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5163412
Share on other sites

Dang namit! I think this could be my problem. The plugs I was recommended by the ngk book were BCPR6ES, standard copper. but the plugs I pulled out are BKR5EIX, iridium. Now which ones should I be using? BKR5 or BCPR6? Also what is the difference between the two? Besides being copper and iridium.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5164257
Share on other sites

Dang namit! I think this could be my problem. The plugs I was recommended by the ngk book were BCPR6ES, standard copper. but the plugs I pulled out are BKR5EIX, iridium. Now which ones should I be using? BKR5 or BCPR6? Also what is the difference between the two? Besides being copper and iridium.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5164258
Share on other sites

The 5 and 6 (i.e. the number) is the heat rating of the spark plug. The higher the number, the hotter the plug, and warmer plugs are used for turbo cars because boost causes more combustion chamber heat. If your book recommends you run the 6s, and your current plugs are 5s, then this would certainly be your problem...

Make sure they are gapped correctly though, the gap should be listed in the NGK book you've been reading.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5164436
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...